Hi everyone,
This is my first post here. I am planning my 2015 setup and had a question. I will try to keep it simple.
I want to outline my house in pixels. My house is small and very close to the street, so I wanted to try to put a single controller in the garage and run most of the wiring from there. To save money on wiring, and since I am not running a lot of pixels (yet), I wanted to daisy chain the different sets of lights together.
My question is this: if I daisy-chain my pixels, is it easy to separate them into discrete sets in the sequencing software? Or would I be better off getting a PixLite 16 instead of the 4 so I can run a separate wire to each set?
Attached is a diagram of my proposed setup to explain what I want. Please ignore the solid white boxes I used to censor my street address.
Yes, it's (relatively) easy to segment these into separate, but connected display elements in the various software (which are you planning to use?)... once you wrap your head around how it works. As you state, connecting strings saves on wiring, but also on null pixels, resistance loss, etc. It just takes a bit more work in the sequencing and controller setup.
You've already noted that you'll need power injection, but you might rethink your layout just a bit to make this even easier. If you put your controller at the far left of the garage (near the front entrance), you could treat both strings lining the garage as one long string with data connected at the far right bottom of the garage. You could then power that long string at the beginning and the end (you still might need supplemental power along the way).
You can also use the strings around the entrance and front of the home as data carriers for the strings in the yard (assuming they're same data type). Of course sometimes it's easier to run separate wires from the controller to avoid remote power injection.
Any time you have dedicated data wires running anywhere near where your strings are, consider using those strings as your data wires and just connect new strings into the end of them. Of course the refresh rate suffers a bit, but only noticeably so when you're at 100's of pixels per string.
With your setup (which is quite similar to what I'm planning), you could do it all with maybe as few as 3 or 4 long connected strings and two or three power supplies.
apollosmith wrote:Yes, it's (relatively) easy to segment these into separate, but connected display elements in the various software (which are you planning to use?)... once you wrap your head around how it works. As you state, connecting strings saves on wiring, but also on null pixels, resistance loss, etc. It just takes a bit more work in the sequencing and controller setup.You've already noted that you'll need power injection, but you might rethink your layout just a bit to make this even easier. If you put your controller at the far left of the garage (near the front entrance), you could treat both strings lining the garage as one long string with data connected at the far right bottom of the garage. You could then power that long string at the beginning and the end (you still might need supplemental power along the way).
You can also use the strings around the entrance and front of the home as data carriers for the strings in the yard (assuming they're same data type). Of course sometimes it's easier to run separate wires from the controller to avoid remote power injection.
Any time you have dedicated data wires running anywhere near where your strings are, consider using those strings as your data wires and just connect new strings into the end of them. Of course the refresh rate suffers a bit, but only noticeably so when you're at 100's of pixels per string.
With your setup (which is quite similar to what I'm planning), you could do it all with maybe as few as 3 or 4 long connected strings and two or three power supplies.
This is all great advice, thanks! I thought hard about the best location for the controllers and will now probably place them in the yard. I think I ordered enough cable to put them virtually anywhere, but I can always supplement from Home Depot.
Boy, the situation with these sequencers is messy. Since I'm just starting out I went with Pixels everywhere I could, so I want full nutcracker support. Every workflow I looked at besides a sequencer with nutcracker integrated seems overly complicated. The only sequencer with full Nutcracker support, and a nice UI, at the moment is... nothing? xLights 4 is not out yet, but will have a sequencer added. Vixen 3 is getting support for the new nutcracker rewrite, but it's not there yet either. I'm unsure what to learn while I wait. Any thoughts?
This Blog Post will help: http://blog.holidaycoro.com/2013/04/outlining-your-house-in-rgb-lights.html
I put up a sample, just moved your controller to the opposite side of your garage. Having pixel counts would help, but I put some arrows in where power could probably be injected both directions. I ignored power for the icicles, I ignored the trees as well.
Modification: The arrow/injection above the middle of the garage would probably be better off on the upper/right side of the garage.


