Controller to pc se...
 
Notifications
Clear all

Controller to pc setup

12 Posts
4 Users
0 Reactions
3,230 Views
Posts: 97
Topic starter
(@thyndman)
Estimable Member
Joined: 15 years ago
[#42977]

Another stupid question.

New this pixels this year. Using an Alphapix16 controller. Plan on using xlights. From what I understand the controller gets connected to the router. The router is also connected to the pc and the Internet, as it currently is for the Internet. The question is, can the pc still use the Internet as it currently does? The controller has an IP address, does that needs to be entered into the network setup? Are there multiple IP address? The pc and controller? Am I over thinking this and making it more confusing. Can still blame memory loss on the new wife.

Thanks
Tom


11 Replies
TazChaLet
Posts: 3042
(@tazchalet)
Famed Member
Joined: 13 years ago

yes you can use internet, the computer has a ip address of something lets say (192.168.0.100) you have too set the controllers ip to something like (192.168.0.200) see how the first 3 sets of numbers match? so the computer and controller are on same network and it can reach the controller, knowing what your ip is of the computer is easy click start, run, type in cmd and in command promp type (ipconfig) look for (ipv4) and that is what your ip on computer is so reset the controller using buttons if you need too to same thing except last number need to be different then use browser and type in ip you set the controller to and see if it connects


Reply
dpitts
Posts: 1020
(@dpitts)
Noble Member
Joined: 16 years ago

If you need help call me. Number on PixelController.com.


Reply
Posts: 97
Topic starter
(@thyndman)
Estimable Member
Joined: 15 years ago

Thank you for your help. Doesn't sound too bad.
Tom


Reply
Posts: 97
Topic starter
(@thyndman)
Estimable Member
Joined: 15 years ago

David, thank you for your offer and assistance. I may take you up on it if I can't get it to work.

Tom


Reply
Posts: 97
Topic starter
(@thyndman)
Estimable Member
Joined: 15 years ago

Finally getting around to setting this up. The problem seems to be that the pc is set to automatically find IP address. I changed this setting and entered 192.168.0.1 and have no internet connection. I did the ipconfig, ip displayed was 192.168.1.5, When I entered that IP address it still will not connect to the Internet. The ip on the controller is pre set to 192.168.0.50. I think I'm close but just not there yet. What setting am I missing?

Thanks

Tom


Reply
TazChaLet
Posts: 3042
(@tazchalet)
Famed Member
Joined: 13 years ago

you can use the buttons on the controller too change the ip that is set for it change it too something like 192.168.1.??? (I use 206) for mine and let your computer get its ip from router like normal once you reset the controller try too connect to it with the ip address you changed it too


Reply
Posts: 97
Topic starter
(@thyndman)
Estimable Member
Joined: 15 years ago

Thanks, will give that a try.

Tom


Reply
Posts: 97
Topic starter
(@thyndman)
Estimable Member
Joined: 15 years ago

I changed the IP address of the controller to that of th pc. The controller is still set as a static ip, the pc is set to automatically get ip. Will that make a difference?
I pinged the IP address and all was good. Ran the test in x lights and the strips light up and change colors. I think it may be working.
Thanks for all the help

Tom


Reply
Posts: 97
Topic starter
(@thyndman)
Estimable Member
Joined: 15 years ago

Ok, one more question. When I add the second controller, I'm guessing the IP address should set to something higher that the first controller. The first one is 192.168.1.50, so the next on could be 192.168.1.60?
Does the second controller just get pluged into the router/switch with the cat 5 cable? My second controller is an alphapix 4, first one is the alphapix16.

Thanks
Tom


Reply
Page 1 / 2
Share: