This is more of a pixel controllers versus props versus power question.
I have my display converted to pixels from incans over the years and I've encountered a few problems.
My props are spread out over the yard.
all ws2811 12vdc pixels
megatree has 32 channels and 2 e682 controllers handle that prop using 4 power supplies
arches have 8 channels and a single e682 controller handles those using 2 power supplies
etc
etc
Pixel poles have 7 channels and a single e682 controller, due to the distances between poles and pixel count per pole I use 2 power supplies to run them. If I add another prop to that controller I encounter problems with misfires and all white lockups.(I have already changed the SIP resistors to account for the long null lengths between controller and pole
Arches have to be split to 2 groups, e682 ports 1-1 to 1-4 and 3-1 to 3-4 to allow proper power to run them due to power consumption leaving 8 channels/ports on that e682 empty
Everything is wired, no wi-fi used.
My star uses a serial driven Px1 due to its isolated location but that requires a com port and I would like to change that to join the rest of my e1.31 universe.
most of my props are in the 5-8 channel count and using only half a controller seems wasteful.
using 2 e6804's to replace 1 e682 adds more data lines and control boxes to the yard and I dont have enough 6804's so before purchasing more I would like recommendations
I am adding more props in the 5-8 channel range this year which may only increase wasted channels per controller depending on location in the yard
Also several 1 channel props are being added (Px1 controlled) which adds to even more com ports and/or cat5 daisy chaining across the yard
Now to the questions;
What controllers are available out there that offer 4 to 8 channels?
What can be used to convert a serial Px1 to e1.31/sCan?
Suggestions to add/inject additional power supplies single power input controllers
Controllers for what? Pixels, AC lights, servos, or something else?
And what are your preferences (or constraints) on the interfaces back to home?
And, for that matter, are your preferences for data streaming or for data stored locally on the controllers?
all ws2811 12vdc pixels
sACN/e1.31
running from a desktop
Steve,
SanDevice has a 4-port controller in stock - https://sandevices.com/product/e6804-kit/
For the conversion of sCan/e1.31 I use a couple of different methods. I us the Renard Plus 4 Output Combo, which haven't been in stock for a while. For some reason, people don't like to build stuff from the board up anymore. I am glad to have gotten them when I did.
In the same realm, there may be people out there willing to give up old Renard plus WiFiBridges. But as the name implies, it is ESP-01 based. I have a few of these I toyed with, but I am like you, I prefer cable.
I am not a coding guy, but I am curious if it is possible to get a DMX firmware load for the the PX1? If so, then something like Pixel2DMX from Experience Lights would do the job.
Maybe the easiest thing to do is use an RS485 to Ethernet adapter. Granted, you will still need to attach a COM port from your computer to the "server" side, but then it plugs into you network so the distant end can come out some else in the network (need 2 availible IP addresses). I used the one in the hyperlink above for a couple of year before I got the RP 4 Output Combo. It works like a champ at 57.6k but I have not tried it at 115.2k, but still should work. I will warn you the instructions are pretty poor, but it can be figured out with a little thought.
I hope this helps,
-Tony
What about the PB16 and BBB16 family?
I finally got around to using my PB16 this year to drive a seed matrix (14X120) and a few spinners.
You can add expansion boards and differential receivers.
Scott has expanded that line so much over the past year or so.
If you need a bare board, I may have one or 2 left.
