C9 Pixel String Rec...
 
Notifications
Clear all

C9 Pixel String Recommendations

11 Posts
6 Users
0 Reactions
2,359 Views
MichiganLights
Posts: 479
Topic starter
(@michiganlights)
Prominent Member
Joined: 14 years ago
[#56498]

I'm looking to add pixel strings next year and wanted to get my research in ahead of time.

So I'm looking at the C9 bulb size or larger. I see snow one day then rain the next so sealed bulbs/pixels are a must. Ready made or bulk strings are fine.

What manufacturer or supplier(s) do you recommend?


10 Replies
Posts: 376
(@k-state-fan)
Reputable Member
Joined: 16 years ago

I have had pixabulbs from diyledexpress and have not had any issues. This is season 6 with them.


Reply
Posts: 113
(@cmndr-brain)
Estimable Member
Joined: 9 years ago

I kind of depends on how you plan on mounting them. For my setup, I chose to go through Ray Wu @ aliexpress and got the technicolor bulbs. Mine are zip-tied to 1/2" pvc and those make easy mounting. The only issues I've had were half dead strings upon receipt.
But, a credit to Ray Wu, he resolved any issues to my w/o hesitation and to my satisfaction. I also took the extra precaution and put a little silicon caulk where the wires enter/exit each bulb enclosure. Fingers crossed. Only had 1 bulb fail after the build was completed. https://www.aliexpress.us/item/2251801767047129.html?spm=a2g0o.productlist.0.0.1ec812e9C1hFZv&algo_pvid=5a4dded3-194c-471c-b1e6-f51d1a1016eb&algo_exp_id=5a4dded3-194c-471c-b1e6-f51d1a1016eb-32&pdp_ext_f=%7B%22sku_id%22%3A%2256547992509%22%7D&pdp_npi=2%40dis%21USD%2136.0%2136.0%21%21%21%21%21%402101e9d216707927626874988e86cf%2156547992509%21sea&curPageLogUid=7lnVJnHUFt2s


Reply
MichiganLights
Posts: 479
Topic starter
(@michiganlights)
Prominent Member
Joined: 14 years ago
Cmndr Brain wrote:I kind of depends on how you plan on mounting them. For my setup, I chose to go through Ray Wu @ aliexpress and got the technicolor bulbs. Mine are zip-tied to 1/2" pvc and those make easy mounting. The only issues I've had were half dead strings upon receipt.

Little off topic, if the bulb/node is dead can you simply splice in a new one? I'm not familiar how the addressing works for individual pixel bulbs.


Reply
Posts: 113
(@cmndr-brain)
Estimable Member
Joined: 9 years ago
MichiganLights wrote:Little off topic, if the bulb/node is dead can you simply splice in a new one? I'm not familiar how the addressing works for individual pixel bulbs.

In short, Yes. Assuming standard WS2811 bulbs. But, sometimes you would change the defective node and maybe the one before it. There are 3 wires, (V+ Data Gnd). You would cut out the bad node and solder the 3 wires, both in and out (make sure power is off). You would need to seal/water proof the connection. Do NOT use regular caulk because it as acidic properties and will corrode your copper wires. Either use 100% silicon and heat shrink or many of us have switched to adhesive lined heat shrink.

To answer your addressing question. Each light is called a node. Your controller sends a stream of data, RGB for each node, 8bits each color for a total of 24 bits (assuming not RGBWhite). The first node peels off the first 24bits of RGB and passes on the rest of the data stream to the next node which will peel off the next 24bits and passes the rest until the last node is reached. As each node passes the data, it will, supposedly, clean and boost the signal to the next node.


Reply
Page 1 / 3
Share: