5v pixels are also only dealing with 1/5th the power dissipation should there be a power/ground short. While it is still mathematically possible that it could ignite the epoxy, I have yet to hear of a single 5v pixel fire.
I realize 11 month have gone by but you might consider migrating to pixels that use the GS8208 controller over time. I stumbled across this controller on the AusChristmasLighting forum. The GS8208 will operate reliably at 12V unlike the ws2811 that has an Absolute Maximum rating of 12V and small over voltage events can stress the chip and increase the probability of failure. Moreover, compared to regulated pixels that incorporate a 5V linear regular, pixels using the GS8208 do not have as many MLCC capacitors which improves reliability as well. The GS8208 incorporates a 12 bit gamma corrected PWM generator for each LED which provides better colours. I have attached a block diagram from the datasheet below.
The LED's are electrically connected in series so the maximum current is 1/3 of the maximum current of a pixel with a ws2811 controller. Thus the GS8208 pixel is generally more power efficient than a ws2811 pixel. Note that because of the series connection, reducing brightness does not reduce pixel current. So, you can connect the same number of pixels to a port as you can with ws2811 pixels (about 280) but you can achieve full brightness (100%) and dynamic range of the pixel.
The GS8208 also has a redundant data input. Overall, it appears to be a much improved pixel controller compared to the ws2811. In the past I stayed away from 12V pixels because of the safety concerns and used 5V for everything. I've ordered some GS8208 pixels this year to try them out myself. There are a few forum threads on AusChristmasLighting forum discussing them.
steve123wrote:
I realize 11 month have gone by but you might consider migrating to pixels that use the GS8208 controller over time. I stumbled across this controller on the AusChristmasLighting forum. The GS8208 will operate reliably at 12V unlike the ws2811 that has an Absolute Maximum rating of 12V and small over voltage events can stress the chip and increase the probability of failure. Moreover, compared to regulated pixels that incorporate a 5V linear regular, pixels using the GS8208 do not have as many MLCC capacitors which improves reliability as well. The GS8208 incorporates a 12 bit gamma corrected PWM generator for each LED which provides better colours. I have attached a block diagram from the datasheet below.
The LED's are electrically connected in series so the maximum current is 1/3 of the maximum current of a pixel with a ws2811 controller. Thus the GS8208 pixel is generally more power efficient than a ws2811 pixel. Note that because of the series connection, reducing brightness does not reduce pixel current. So, you can connect the same number of pixels to a port as you can with ws2811 pixels (about 280) but you can achieve full brightness (100%) and dynamic range of the pixel.
The GS8208 also has a redundant data input. Overall, it appears to be a much improved pixel controller compared to the ws2811. In the past I stayed away from 12V pixels because of the safety concerns and used 5V for everything. I've ordered some GS8208 pixels this year to try them out myself. There are a few forum threads on AusChristmasLighting forum discussing them.
I've been advised you need to be careful where you get them because there are counterfeit GS8208 controllers lurking in the wild.
Thanks for the thought Steve....I hadn't heard much about the GS8208's. I just converted all the pixels on or around the house to EVO's this year. We'll see if that makes a difference..... I just couldn't put those fire pixels back up again this year....
Speaking of taking care where you buy......the 'fire pixels' were purchased from a 'known/trusted' source that everyone on the site knows and most use his pixels.....The sad thing is I've used his pixels for years and one of the batches of >5,000 purchased probably 5 years ago has only had 1 failed pixel over all those years and it simply stuck on as a red 'glower'.....Go figure. The 'fire' pixels obviously were either a bad batch or a failure of a redesign/manufacturing cost cutting effort since they are slightly shorter than the earlier good batch..... I just can't take a chance anymore to run his pixels on or near the house.
Speaking of taking care where you buy......the 'fire pixels' were purchased from a 'known/trusted' source that everyone on the site knows and most use his pixels.....The sad thing is I've used his pixels for years and one of the batches of >5,000 purchased probably 5 years ago has only had 1 failed pixel over all those years and it simply stuck on as a red 'glower'.....Go figure. The 'fire' pixels obviously were either a bad batch or a failure of a redesign/manufacturing cost cutting effort since they are slightly shorter than the earlier good batch..... I just can't take a chance anymore to run his pixels on or near the house.
EVO's are probably ok too but there isn't much information other than they appear to have the controller and LED integrated (like pixel strips). Mattos claims UL certification but I checked the UL listings and there is no listing for Mattos Designs. Someone explained to me that Mattos claim UL certification but that only the wire is certified. I don't know what all the facts are but I did I reached out on one of the forums to get clarification and instead of answering the question someone said to call JR and he would explain. I don't think there is anything to explain when you claim UL compliance. Either you are or you are not. So, my suggestion to be to ignore the claim of UL certification and treat them like any other pixel and use them accordingly.
The bullets have been problematic for a while now. I did a lot of tear downs on a lot of pixels a few years ago now to try and figure out what was going on. What I determined is that the failures are likely due to manufacturing problems. The regulated pixels in particular have ceramic capacitors adjacent to the board edge and the boards were being V-scored for singulation. These processes very likely induce mechanical stress on the capacitors which can crack them. When an MLCC cracks it can short circuit which can cause a catastrophic failure. We published the results and a very boring YouTube video. I have heard some vendors are now milling the boards instead of v-scoring them. Hopefully the vendors are also using reliable suppliers for the MLCC capacitors as well. Still, avoid pixels where the capacitor(s) are close to the board edge.