Renard Pixel String
 
Notifications
Clear all

Renard Pixel String

62 Posts
16 Users
0 Reactions
32.9 K Views
Posts: 84
Topic starter
(@cypress1138)
Trusted Member
Joined: 18 years ago
[#10359]

I have been lurking on this forum for quite some time and have been amazed at the RGB pixels that have been done (I’m pointing at you MPH and JEC!) but these seem to be very complex and expensive. Specifically, I am referring to the smart pixel in that each RGB led or pixel has its own microcontroller meaning that the cost per pixel is very high. If a modified version of the Renard firmware was written for a different pic with a higher pin count say the 16F628A this one controller could drive 8 RGB leds or in effect 24 leds. By connecting all of the red leds together, all of the green leds together, and all of the blue leds together and then strobing each led you could control 8 RGB leds with 11 pins. The current firmware only uses the first 8 bytes after the command address and then any remaining bytes it just echoes down the line. Now I have 4 questions:
1. Am I completely crazy?
2. As near as I can tell from the wiki and what I’ve found so far is that packet format is byte 0 = sync byte, byte 1 = command address byte , bytes 2-9 dimmer levels. Now is the 10th byte another command byte+1 (0x81) or is it another dimmer level?
3. Any reason why the firmware could not be modified to use 24 bytes after the command byte before echoing any further bytes?
4. Am I completely crazy?


61 Replies
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago
cypress1138 wrote:
1. Am I completely crazy?
4. Am I completely crazy?

Yes and Yes :p (j/k)

Welcome to DIYC!

Actually there is a thread here somewhere about using a multiplexed DMX controller to provide LED matrix abilities but it's still in the 'will it work?' stages at this point. I would think if the HW for this is nailed down it would not take much to do the same with Renard protocol.

Edit - here is the thread: http://doityourselfchristmas.com/forums/showthread.php?t=10302 - while the OP is regarding a specific application, the HW should be applicable to multiple applications.


Reply
kychristmas
Posts: 3955
(@kychristmas)
Famed Member
Joined: 18 years ago

Join Date: Oct 2008
Posts: 1

Man, you have been lurking haven't you?


Reply
Cheater
Posts: 114
(@cheater)
Estimable Member
Joined: 17 years ago
cypress1138 wrote:If a modified version of the Renard firmware was written for a different pic with a higher pin count say the 16F628A this one controller could drive 8 RGB leds or in effect 24 leds.

I'm working on a Renard compatible design (Vixen wont know the difference and connections will be the same as a Renard24) with 24 channels coming off a single chip.
The chip I'm designing around is a ATmega16. Usually costs around $5. 🙂


Reply
mrpackethead
Posts: 2289
(@mrpackethead)
Famed Member
Joined: 19 years ago
cypress1138 wrote:I have been lurking on this forum for quite some time and have been amazed at the RGB pixels that have been done (I’m pointing at you MPH and JEC!) but these seem to be very complex and expensive.

Which pixel are you referring to? the classic pixel? or our more recent strings of pixels. The new pixels are about $2 each.. I really did'nt think that was expensive?

If a modified version of the Renard firmware was written for a different pic with a higher pin count say the 16F628A this one controller could drive 8 RGB leds or in effect 24 leds.
By connecting all of the red leds together, all of the green leds together, and all of the blue leds together and then strobing each led you could control 8 RGB leds with 11 pins.

Yes, you could do something like that. Are you going to space the 8 RGB leds apart? Don't underestimate the cost/effort of housing the leds. If you can build what you are talking about for less than the new pixels, i'll be very very impressed.

>1. Am I completely crazy?

no


Reply
Page 1 / 13
Share: