DMX code for renard...
 
Notifications
Clear all

DMX code for renard???

33 Posts
12 Users
0 Reactions
22.8 K Views
RavingLunatic
Posts: 1502
(@ravinglunatic)
Noble Member
Joined: 19 years ago
P. Short wrote:
3) Terminator Resistors

The default BOM for all of the Renard boards has a 120 Ohm terminator resistor across the RS485 lines. This doesn't work well with DMX512 in most situations, so you should remove these resistors from the Renard-DMX boards, and use the prescribed DMX termination methods.

It will be interesting to see what happens when using Frank's Renard2DMX board and connecting a bunch of Renard boards to the DMX line. I'll wait to do any de-mods til after I do some experimenting to see what happens. I'm not too worried about sticking to the "DMX code" as long as it works.

Education Time:

After your comments and actually thinking about the circuitry (instead of just accepting it as is), it appears that the data input circuitry is setup the way it is so that it can handle the RS232 signal. Is that correct?

If it is, then it would be perfectly acceptable to omit those components on a future board if you intend it to only handle RS485 (DMX) and not RS232, right? Just feed the input directly into the 75176 chip (or suitable sub).

Just thinking ahead to next year.


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

Yes. I had forgotten about the two zeners. They can be left off for DMX use, thereby reducing the capacitance on the RS485 inputs.

The purpose of the two 1K resistors and the two 27K resistors is to provide fail-safe biasing for the inputs. This means that the output of the RS485 chip goes to a guaranteed high state if the inputs to the board are either left high or shorted together. This is from one of the TI application notes, and I'm not sure if the resulting design meets the DMX512 specs.


Reply
Posts: 14
(@darko)
Active Member
Joined: 18 years ago
P. Short wrote:
.....

2) Multiple boards

There are two different ways for you to connect multiple Renard boards to a DMX controller.

The preferred method is to connect all boards in parallel to the DMX512 cable. The first PIC on each board will be programmed with the desired DMX address for that board, and all other PICs on the board will be programmed for address '1'. In this situation you will only use the input connector on each Renard board, and the output connector will be left open.

The alternate (non-preferred) method is to daisy chain the Renard boards in the same way that you would with Renard non-DMX firmware. The first PIC on the first Renard board will be programmed with the desired DMX address (1-512), and all of the rest of the PICs (the remaining PICs on the first board, and all of the PICs on the remaining boards) will be programmed with address '1'. The advantage of this scheme is that it is easier to set up (fewer PICs with non-default addresses, fewer adaptor cables/boards required). The disadvantage is that it is much more difficult to intermix Renard-dmx boards with other types of DMX devices, and there is less flexibility in assigning DMX addresses.

I was just staring at the renard24 DMX converter board schematic, and I finally see what you mean by "Parallel" wiring.

Does this neccessarily mean that, with some future design, we could have a renDMX board that can be either daisied OR wired with a star-like (parallel) topology? Is it possible to have hybrid layouts with "subcontrollers" spoking off of more centralized daisy-chained controllers?

If so, yikes, thats cool 🙂


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

DMX512 only supports a linear topology (unless you use some sort of active repeater to provide for branches). While you could use the Renard-DMX board as an ad-hoc repeater, I don't think that this would be a good idea. You would end up driving yourself crazy handling the addressing complexities.


Reply
Posts: 14
(@darko)
Active Member
Joined: 18 years ago

By addressing complexities, are you referring to the need to have to individually program each controller with a start address?

If thats the only issue, I think I would actually be comfortable with that. Perhaps I could sharpie the start addresses onto each enclosure. Maybe ICSP can be used too.

EDIT

Let me clarify. By "Daisy Chain", I was simply referring to the DMXin and DMXout ports on the converter board. I wasn't referring to wiring the out port to the last pic in the onboard chain.

I guess since the DMX board itself has the DMX In and Out ports wired in parallel, there really is no distinction anymore right? Everything is parallel, so does it require a linear topology?

For future designs (which incorporate the ren + DMX coverter circuitry) we could daisy chain (in a parallel sense), but also use passive splitters where we need to produce branches?


Reply
Page 4 / 7
Share: