Notifications
Clear all

Router mod

12 Posts
7 Users
0 Reactions
4,148 Views
Keebler
Posts: 1691
Topic starter
(@keebler)
Noble Member
Joined: 18 years ago
[#31368]

is there a known way to convert a standard router to RECEIVE the encrypted wifi signal through the antenna and make it available to the attached ports?


11 Replies
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

We used the name "Workgroup Bridge" for this type of configuration when I was in the wireless group at work. I doubt that most home router/APs can be put into that mode using standard software since they are normally used as an access point. I would think however that with hacked code on the appropriate model router/AP it could be done - you'll have to dig around for that of course.


Reply
Keebler
Posts: 1691
Topic starter
(@keebler)
Noble Member
Joined: 18 years ago

thanks Brian. i appreciate that!
🙂
since they are old routers i dont care one bit to hack em


Reply
Posts: 3735
(@algerdes)
Famed Member
Joined: 15 years ago

Perhaps DD-WRT will work as a replacement firmware on the routers you are using. If memory serves (and I don't mind being corrected on this) DD-WRT has the ability to be put into bridge mode. It is very good and is even the primary firmware on a lot of new stuff.

Note that the WiFi side of most routers is directly connected to the LAN ports. The router is usually connected to the WAN port and does not have to be used (as in you can ignore it). I've done bridges like this all over the place. LAN BRIDGE .......... BRIDGE LAN.


Reply
bitelf
Posts: 57
(@bitelf)
Trusted Member
Joined: 16 years ago

Depending on the model of your old router (not all are supported), you might consider flashing them to DD-WRT. CISCO "Workgroup Bridge" is called "client bridge" mode in the feature rich universe of DD-WRT. With the right router, you can get DD-WRT to do some neat stuff.


Reply
Keebler
Posts: 1691
Topic starter
(@keebler)
Noble Member
Joined: 18 years ago

AWESOME
thank you all 🙂


Reply
Kev7274
Posts: 2037
(@kev7274)
Famed Member
Joined: 13 years ago

I got a couple routers with DD-WRT flashed onto them. Not used them in a while,but the firmware is very configurable.


Reply
Posts: 1115
(@11bravo)
Noble Member
Joined: 14 years ago

I have two Desktop PC's located in different rooms. I changed two Cisco Linksys E1200's to DD-WRT so they could communicate wirelessly from the desktop PC's to a CradlePoint router in another room that was wired USB to a AT&T air card.

I plan on testing to see if I can using them to communicate from Show PC to a E682 about 300 feet away from the house. The power out can be adjusted up 251mw on them.


Reply
Posts: 2171
(@mschell)
Noble Member
Joined: 18 years ago

As others have mentioned, it's all about if the router can be put in "bridge" mode. This just allows all packets to flow between the "LAN" ports and the wireless connected network. There's no routing or isolation between. Most Linksys routers have this built into their stock firmware. Many others may have it, depends on the manufacturer and the firmware.

If the hardware is capable of running DDWRT or OpenRouter or some other non-stock firmware, then it's much more "better" to be able to use bridge mode. Note that the WAN port of the access point/router typically won't be active in this mode.

I would highly recommend that other end of the wireless network be a separate access point from your normal home network. Otherwise you run the risk of making the regular users of that network, i.e. your family, very unhappy when you start running lots of traffic outside.


Reply
Posts: 3735
(@algerdes)
Famed Member
Joined: 15 years ago

I agree.

Your show network (wired and wireless) really needs to be isolated from your "regular" network, at least during production. (You may intertwine during setup, but unhook them during "show time".) As we get deeper and deeper in the channel counts, and faster and faster in cycle rates, the networks are getting inundated.

We do this same thing in Audio (stage performances). We can now take literally hundreds of live audio connections and feed them down one Ethernet cable to the control board, then back again to feed speakers, monitors, headphones/ear buds, and even off-stage rooms. Works great, but experience shows that you don't want to use it for other traffic unless you like listening to crowds and performers ranting directly at you.

As far as the wireless, I have one Wireless Access Point set as a master bridge that has the capability to talk to multiple bridge points. Works great. Since most show software is one-way (at this time) the constant one-way-traffic has the potential of tying up the switch portion of the access-point and not allowing other traffic to get through. (Not a real problem these days, but it does happen.)


Reply
Page 1 / 2
Share: