In addition to RGB pixels, I will want the ability to switch some AC devices on/off. But I can't seem to find any controllers to do this other than the one from LOR CTB16PC. But I think it only takes commands over the LOR proprietary network. Is there an AC controller that works over DMX or E1.31?
lwillisjr wrote:In addition to RGB pixels, I will want the ability to switch some AC devices on/off. But I can't seem to find any controllers to do this other than the one from LOR CTB16PC. But I think it only takes commands over the LOR proprietary network. Is there an AC controller that works over DMX or E1.31?
The lor controllers can do dmx as well.
James
Sent from my SM-G900V using Tapatalk
I know their 24 channel dumb RGB controller can as it has jumper settings on the board for LOR or DMX. I wasn't so sure about the AC controller but will give it a try.
Renard controller's work over serial, rs232, rs485.
What controllers are you using to run your RGB pixels?
In the DMX lighting world, for higher power stuff, look for DMX dimmer/relay packs. Dimmer has dimming. Relay is ON/OFF. Some packs can be configured either way. Some turn on at 5% DMX Dim, and others switch at 50%. May be other values used to decide ON, but the most common are listed. Most are for Indoor use, so protect from the elements. Due to higher power, most are only 4 channel.
You can also go with the Renard SS controllers and get a DIYLEDExpress E1.31 Bridge. It is very easy to setup and works great I run about 10 different Renard boards for my Incan and LED A/C lights. If your not in a rush there will be a group buy for Renard boards and you can get them pretty cheap but you have to build them yourself.
lwillisjr wrote:Is there an AC controller that works over DMX or E1.31?
Lynx Express or Minleon Express or xDMX to name a few
There are many options for DMX control of AC. I do not know enough to pick or pan any of them. I have 3 factory built LOR CTB16PC's but no other AC controllers to compare against.
This year, I switched everything over to E1.31. I have an E682 that I configured for DMX output for the LOR boxes and a DMX RGB controller.
I had a number of initial problems that all tracked back to a bad RJ-45 cable and a bad RJ-45 connector. When I fixed those problems, everything worked great. There were no controller related issues.
The LOR boxes convert their device ID to a starting DMX channel number (ID 1 = DMX chan 1; ID 2 = DMX chan 17; etc) as you have to set that as appropriate.
LOR boxes use a different RJ-45 pinout than the DMX standard. I made my own converter cables. It was easy.
You do not have to "configure" the LOR box for DMX. You just plug it in (the LOR protocol and DMX protocol use the same "physical transport layer" protocol which allows the LOR box to auto sense/configure LOR vs DMX).
I think the LOR boxes are a good value for a beginner. For an advanced user that understands the trade-offs and is handy with a soldering iron, there are likely options that will fit your needs better.
Jerry-Rigs wrote:There are many options for DMX control of AC. I do not know enough to pick or pan any of them. I have 3 factory built LOR CTB16PC's but no other AC controllers to compare against.This year, I switched everything over to E1.31. I have an E682 that I configured for DMX output for the LOR boxes and a DMX RGB controller.
I had a number of initial problems that all tracked back to a bad RJ-45 cable and a bad RJ-45 connector. When I fixed those problems, everything worked great. There were no controller related issues.The LOR boxes convert their device ID to a starting DMX channel number (ID 1 = DMX chan 1; ID 2 = DMX chan 17; etc) as you have to set that as appropriate.
LOR boxes use a different RJ-45 pinout than the DMX standard. I made my own converter cables. It was easy.
You do not have to "configure" the LOR box for DMX. You just plug it in (the LOR protocol and DMX protocol use the same "physical transport layer" protocol which allows the LOR box to auto sense/configure LOR vs DMX).I think the LOR boxes are a good value for a beginner. For an advanced user that understands the trade-offs and is handy with a soldering iron, there are likely options that will fit your needs better.
Very well stated. I think users will get a lot from your post.
James
Sent from my SM-G900V using Tapatalk
