Buffer/line driver ...
 
Notifications
Clear all

Buffer/line driver - null pixel without pixel

347 Posts
90 Users
0 Reactions
197.7 K Views
RobG
Posts: 1255
 RobG
Topic starter
(@robg)
Noble Member
Joined: 14 years ago

Yes, RS485 is the best thing to use in this situation.
However, I am trying to keep this board as simple and as cheap as possible and at the same time, compatible with existing cabling (using RS485 would require additional wire.)

Ringing, reflection, and impedance mismatch is not my concern (since I don't know what hardware this board will be used with,) you will have to take steps to reduce them.
My concern is cable capacitance and its effect on the signal. My board will reduce this effect by isolating long stretches of wires and by using strong driver. It will also reduce reflection and ringing because of the isolation.

@MT, yes, you should be able to increase the distance, but to a degree.


Reply
Posts: 255
(@rogerh)
Reputable Member
Joined: 12 years ago

The cable I made is 100 feet. I only needed 70 feet but thought it would give me options. No issues with the cable length.


Reply
MindTrik
Posts: 1542
(@mindtrik)
Noble Member
Joined: 16 years ago

Nice

Sent from my LG-H811 using Tapatalk


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

The cost would be higher, but there are RS485 line drivers and receivers with an SOT23 footprint. They could take power from the source and destination devices, so three wires would be required in the cable between the transmitter and receiver.

That said, the approach taken above is generally simpler and cheaper. The only drawback that I see is the distance limitation, and the need to splice them into the cable at 25' intervals.


Reply
RobG
Posts: 1255
 RobG
Topic starter
(@robg)
Noble Member
Joined: 14 years ago

All valid points, but again, the whole reason for this is to help with existing wiring.
If someone wants to change their approach and go with RS485 for long runs, then they should choose other drivers.


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

OK, then I'm confused. I sort of assumed that if someone has existing wiring, that they already have null pixels attached to the cables. So I'm wondering what would lead someone to remove existing null pixels and replace them with this board. Or are you referring to an existing cable scheme, which they're expanding?


Reply
DrNeutron
Posts: 2018
(@drneutron)
Noble Member
Joined: 14 years ago

I think what Rob is trying to accomplish is to simplify the cabling so nulls are no longer needed. This would effectively eliminate the added complexity of adding nulls to each sequence. For those users that have existing nulls in place, it would require them to go back into their respective sequencing software and remove them if using Rob's board.
This seems like a simple, cost-effective solution.


Reply
RobG
Posts: 1255
 RobG
Topic starter
(@robg)
Noble Member
Joined: 14 years ago

Pixels are not line drivers, so using null pixels helps, but it's not perfect. They have to be part of your sequence, which is also a drawback.
If you want to use it for 100' run and insert driver every 25', then I would say use RS485. If you already have 100' cable with 4 null pixels, then I would suggest swapping them with my boards.


Reply
rstehle
Posts: 4348
(@rstehle)
Illustrious Member
Joined: 19 years ago
P. Short wrote:OK, then I'm confused. I sort of assumed that if someone has existing wiring, that they already have null pixels attached to the cables. So I'm wondering what would lead someone to remove existing null pixels and replace them with this board. Or are you referring to an existing cable scheme, which they're expanding?

There are lots of folks building the Pixel portions of their display for the first time, (like me) and these could come in very handy.


Reply
Posts: 255
(@rogerh)
Reputable Member
Joined: 12 years ago

Here's an easy way to explain it. I have a mini tree using 98 pixels. After pixel 98 I use the signal output and power , 3 wires, conne t it to a max485 chip. from that chip I run a cat5 cable using 2 twisted pairs pretty much as far as I need to. At the end of that cable I use another max485 chip to translate the signal running over the twisted pair of signals back to a single signal. What I end up with is signal and power to go to my next mini tree. Mind you, I will not power anything except the two chips with the cat5 cable. The signal and ground goes to the next mini tree and power injection is used at that point. Roger


Reply
Page 4 / 35
Share: