Expo 2x2 P10 Matrix...
 
Notifications
Clear all

Expo 2x2 P10 Matrix Sequence....

72 Posts
12 Users
0 Reactions
21.3 K Views
Posts: 49
(@ametsman)
Trusted Member
Joined: 13 years ago

This is weird. Yesterday I was able to see this in xLights with no problem. Today when I open the sequence, it shows in the sequence window but not in the preview window. I can't see anything when I run it.


Reply
Posts: 49
(@ametsman)
Trusted Member
Joined: 13 years ago

This is weird. Yesterday the sequence preview worked fine. Today when I open it, it doesn't show in the preview window when I run it. Attached is a pic.

screen

Reply
Posts: 1015
(@gilrock)
Noble Member
Joined: 14 years ago
ametsman wrote:This is weird. Yesterday the sequence preview worked fine. Today when I open it, it doesn't show in the preview window when I run it. Attached is a pic.

Click on Render All or Save first.


Reply
Posts: 58
Topic starter
(@mararunr)
Trusted Member
Joined: 13 years ago
Wolfie wrote:Have yall put a meter or scope on the Vcc line to the BBB/Pi? I suspect that the voltage may be deviating based on pixel brightness. I have been told and seen somewhere in specs on the P10, that they could potentially draw 3a full on. I am wondering if the wire size yall are using in the USB cables feeding the BBB/Pi are too small or the PSU you are using isn't capable of delivering constant voltage as the panels change brightness.

I would also consider putting a ferrite bead on the power cable going to the BBB/Pi as well to filter some of the spiking (EMF and RF) that may be feeding back from the panels.

Nope, haven't done any of that. Once I ran separate power lines I had no more issues and didn't look any further. I'm still fairly new (3rd year) and not an electrical engineer so scopes and ferrites are outside my knowledgebase up to this point. Hopefully this is my last year for adding a ton of props (doubling show each year) and I can do more in-depth stuff next year. So far, all I'm able to do is keep up with building props, getting 'em to work, and then some sequencing.


Reply
Posts: 49
(@ametsman)
Trusted Member
Joined: 13 years ago

Yep, that did it. Thanks!


Reply
Posts: 49
(@ametsman)
Trusted Member
Joined: 13 years ago

Got everything in for this. One question, the wi fi dongle comes with a cd. Do I need to run this for the Beaglebone to be wireless. If so how, or do I just install the dongle into the usb port?


Reply
Posts: 49
(@ametsman)
Trusted Member
Joined: 13 years ago

So now I have everything connected just like it shows in the video. Uploaded the sequence to BBB to run in FPP. Chose that sequence. Made sure it was in scheduler. Went to "Status Page" "Program Control". Clicked on play sequence and nothing happens. Do I have to set the panel layout in FPP? This is how I did it.

Panel

Is there anything else I need to do in FPP or the sequence?


Reply
Posts: 2507
(@mrgrumpy)
Famed Member
Joined: 12 years ago

Click: Enable LED Panel Output
Verify your arrows, and change the right P-1 to P-2 on both O-1 & O-2
Click Save - click Restart FPPD

Also, you may want to try the test page first. Your sequence does not need to be a playlist or scheduled there to work.
You can also just fire a test to the whole screen.

Control/Status TAB
- Display Testing

Test pixels - just click the box.

Click the SEQUENCE TAB to test a sequence
FPP should have already selected the top sequence so just hit play.


Reply
Posts: 49
(@ametsman)
Trusted Member
Joined: 13 years ago

Got the panels working except all 4 panels are doing the same thing.

Panel 2

I must have the led panel mapping wrong somewhere. I am using the sequence made for this.


Reply
Posts: 2507
(@mrgrumpy)
Famed Member
Joined: 12 years ago

I can't verify the arrows, but the layout now looks fine for xLights, and a 2x2 panel.
Not sure about xLights, but I don't map FPP using Vixen. My only configuration is set on this page

You may try changing the layout arrows to point down. That how mine point.
(clink on arrow to rotate)


Reply
Page 4 / 8
Share: