Triks-CBee
 
Notifications
Clear all

Triks-CBee

14 Posts
6 Users
0 Reactions
7,744 Views
rlilly
Posts: 993
Topic starter
(@rlilly)
Noble Member
Joined: 19 years ago
[#6807]

I received my Xbee serial adapter today from Sparksfun, plugged in the Xbee Pro I'd gotten for the Prop 128/Helix. and hooked up to the newly finished Trick-C setup.

Fired it up and verified it works wirelessly without issues. I'm seeing a few more Xbees in my future!

A few pics:

Xbee and serial board
Xbee and Tricks-C
Video of Rotating Message (from behind)


13 Replies
TimW
Posts: 554
 TimW
(@timw)
Honorable Member
Joined: 19 years ago

I was hoping for a shot of scrolling text from 100 feet away! 🙂 and a caption...Look! No wires!...

Nice application.

Tim


Reply
Posts: 41
(@ranger-391xt)
Trusted Member
Joined: 19 years ago

After seeing this post, I decided I wanted to make my setup wireless also.

I used the the same XBee serial explorer board from Sparkfun to connect to the Triks-C. For the PC end, I purchased one of the XBee Explorer USB from Sparkfun.

A couple of things worth mentioning:

1)- Make sure to use the 802.15.4 XBees. These seem to work best for point to point communication. I originally tried the XB PRO ZB ZigBee devices, and wasn't able to get them to function correctly.
2) - In the Xbee configuration set the Interface Data Rate to 57600.
3) - Pin 2 on the DB-9 connector of the XBee serial explorer has to be connected to the TX pin (pin 3 on the DB9 - pin 4 on the RJ-45) of the Triks-C.

I hope this info is useful for anyone else considering going wireless using the XBees and Sparkfun adapters.

Chris


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

Just ordered my TRIKs/-C/LED Panels this week - looks like I might need more goodies to make it easier to set up! I'm also getting a Helix controller which uses an XBee Pro radio - would this be compatible with this? Just curious if the one PC based radio could control both this and the Helix at the same time...

Brian


Reply
Posts: 41
(@ranger-391xt)
Trusted Member
Joined: 19 years ago

I'm am not sure how you would drive both the Triks-C and the Helix using a single XBee on the PC side.

I would think the easiest thing would be to have two XBees connect on the PC, and each would be assigned a different Com: port. For the two XBees used for the Helix connection assign one PAN ID, and use a different PAN ID for the Triks-C XBees.

Chris


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

I think the Helix design will allow you to control multiple controllers from the single PC radio -but not 100% sure. I don't know enough on how the radio addresses are assigned and how the spectrum is shared. I work/test with 802.11abgn WiFi gear every day but haven't worked with this yet - guess I got some reading to do!


Reply
Posts: 393
(@soakes94)
Honorable Member
Joined: 18 years ago

Just wondering, would it be possible to use the ren-w to control the triks-c? This would make an awesome setup I think :p


Reply
LabRat
Posts: 2981
(@labrat)
Famed Member
Joined: 17 years ago
soakes94 wrote:Just wondering, would it be possible to use the ren-w to control the triks-c? This would make an awesome setup I think :p

Yes it should be possible... and I'm planning to go *almost* exactly this. The only difference is that I plan to use a PIX-C (but from the serial stream point of view.. they are equivalent). Have I done it yet? No.. I was playing with an ethernet to RS485 adapter on the weekend and didn't get to the REN-W yet.


Reply
Posts: 393
(@soakes94)
Honorable Member
Joined: 18 years ago
LabRat wrote:Yes it should be possible... and I'm planning to go *almost* exactly this. The only difference is that I plan to use a PIX-C (but from the serial stream point of view.. they are equivalent). Have I done it yet? No.. I was playing with an ethernet to RS485 adapter on the weekend and didn't get to the REN-W yet.

Will you let me know your results?

Thanks


Reply
LabRat
Posts: 2981
(@labrat)
Famed Member
Joined: 17 years ago

But of course... (looking in my crystal ball) Probably not until the weekend.


Reply
Page 1 / 2
Share: