Power problem on le...
 
Notifications
Clear all

Power problem on led light strings

9 Posts
4 Users
0 Reactions
5,370 Views
Posts: 243
Topic starter
(@hockeyhunter1956)
Reputable Member
Joined: 13 years ago
[#51201]

I’m going on 5 years with about 200 Color-Rite led light strings that are used on my wire frame figures that I have built. Last year I noticed that a handful of strings were not as bright as the other strings on the figures. (This was especially noted on the blue led bulbs in the strings …… these strings allow you to interchange bulbs of various colors). I replaced the strings and everything was fine. In diagnosing my problem strings I noted that the voltage output was 1.75 volts. I then tested some new strings I have and found that they output anywhere from 2.70 volts all the way up to 3.0 volts. Since all the bulbs still work on the 1.75 volt strings (they are very dim) I’m wondering if my male 120 volt plug (picture attached) has some how allowed this to occur while trying to drop the voltage down to the desired 2.7 - 3.0 volt output. If so, I would rather replace the plugs (but I haven’t found anything yet online that might work) rather than replace the entire strings when in reality the led bulbs still work. Not to mention the time it takes to unwrap and rewrap the wire frames and the cost of new strings.

Any suggestions would be appreciated.

Thank you.

Electical Plug

8 Replies
Posts: 243
Topic starter
(@hockeyhunter1956)
Reputable Member
Joined: 13 years ago

I would agree with you that the AC portion of the plug most likely is not the problem. The AC plug not only is fused as you suggested but when I disassembled it today I was able to access the “blob” as you described which was located inside of the AC plug housing. (see attached photo) I measured the voltage right where the “blob” connects to the wire for the lights and that is where I was getting 1.70 volts on the poorly performing led strings. I’m not sure what I’m looking at in the photo I’m guessing that I have some type of resistor set up. There really isn’t much to this board. Is it possible to build one or modify my bad boards?

Bridge rectifier 2

Reply
MartinMueller2003
Posts: 7615
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

That is a half wave bridge rectifier. The blob is a capacitor. The corrosion is one potential problem. However, I suspect you have a bad socket somewhere in the string.


Reply
Posts: 304
(@dennis-cherry)
Reputable Member
Joined: 19 years ago

Corrosion is the first thing to fix. Clean it off using soap and water using a toothbrush.

Let it dry for several hours then reassemble and check the output voltage again.

Dennis


Reply
Posts: 243
Topic starter
(@hockeyhunter1956)
Reputable Member
Joined: 13 years ago

I'm not sure that my picture did justice to the problem I'm trying to figure out. I believe what you think is corrosion is actually white silicon that was used by the manufacturer to seal up both ends of the board as it was placed in the plastic housing. It has been tough to remove all of that from the ends of the board. When I look at the board under the magnifying glass, I don't see any corrosion of the board. Just white silicon.

If I did have a bad socket in my strings, I guessing that would be had be rather time consuming to find. But hey, at least I'm still learning in this process.

Thanks for all of the replies.


Reply
MartinMueller2003
Posts: 7615
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

You can use a needle probe at each socket to see if you get the desired voltage progression. One probe stays at the plug and the other probe is moved from socket to socket. A large change indicates the previous socket needs to be cleaned.


Reply
Posts: 243
Topic starter
(@hockeyhunter1956)
Reputable Member
Joined: 13 years ago

That sounds reasonable. I'll start checking the wire frames this week that have the problem strings and see if that does the trick. I've got 40 frames to sort through and report back once I have a chance to check the voltage as you suggested.

Thanks for the suggestions.


Reply
aknflyer
Posts: 371
(@aknflyer)
Reputable Member
Joined: 10 years ago

That is indeed a half wave rectifier. The diode is the only active component. I find at work that if the resistors and that type of capacitor look undamaged, it is the active component that has an issue. I would replace the diode. You could unsolder it and get the Part# off of it and replace (Probably starts with 1N100?) If I knew the max current supported I could reccomend a part. I could mail you one if not available in your area, as your not far from me. Or send me the board and I will replace it for you. I'll PM my address.

FYI blue leds ususally have the lowest lumen (brightness) output compared to the other colors, if you look at the specs.


Reply
Posts: 243
Topic starter
(@hockeyhunter1956)
Reputable Member
Joined: 13 years ago

Thanks for the offer. I sent you a PM.


Reply
Share: