Looking for some St...
 
Notifications
Clear all

Looking for some Strobe LED knowledge

11 Posts
4 Users
0 Reactions
5,752 Views
ChiefWarrant
Posts: 570
Topic starter
(@chiefwarrant)
Honorable Member
Joined: 19 years ago
[#15565]

While researching options for a strobe light to build this year, I read numerous threads, saw many diagrams, but they don't seem to fit my needs, which is just an occasional burst, not the epileptic type, just a burst for emphasis on portions of the squence.

Given how LED's work (at least to my rudimentary understanding), it seems that I should be able to just build a simple (+12VDC)----(Super Bright LED array)----(Resistor) circuit to make this work.

Am I over simplifying the problem, or will my way of thinking not produce a bright flash?

Thank you.

Tony


10 Replies
dirknerkle
Posts: 10311
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

There are samples of LED strobes here and they are generally controlled via Vixen (turn on a pixel or two to fire it). The circuitry isn't terribly difficult and you need very few components to make it work. A resistor thing can work, but more often than not, there's an LM317 in there somewhere as a current-limiter to help protect the LED.


Reply
Helenaguy
Posts: 255
(@helenaguy)
Reputable Member
Joined: 17 years ago

Check out post # 74 in this thread:

http://doityourselfchristmas.com/forums/showthread.php?8639-Anyone-ever-try-to-make-strobes-out-of-old-disposable-cameras/page4

Brad Jones designed this circuit and I have built several very similar (did not use the diode) and they seem to work well using Ren48LSD and 24v power supply. Don't pay any attention to the name of the thread, as it kind of morphed into a discussion on the LED strobe.


Reply
ChiefWarrant
Posts: 570
Topic starter
(@chiefwarrant)
Honorable Member
Joined: 19 years ago
Helenaguy wrote:Check out post # 74 in this thread:

http://doityourselfchristmas.com/forums/showthread.php?8639-Anyone-ever-try-to-make-strobes-out-of-old-disposable-cameras/page4

Brad Jones designed this circuit and I have built several very similar (did not use the diode) and they seem to work well using Ren48LSD and 24v power supply. Don't pay any attention to the name of the thread, as it kind of morphed into a discussion on the LED strobe.

That was the thread that got me thinking about LEDS fro strobes. MY intent would be to run these off a DCSSR, as there are not any plans for me to build a REN48LSD this year.

So as Dirk said above, the LM317 is in there to protect the LED's


Reply
BuzzKill
Posts: 577
(@buzzkill)
Honorable Member
Joined: 19 years ago

Bright flash is a relative thing. Will a bunch of cool white stawhat LED's look like a strobe light at night and in a less lit portion of your program when you light them for a few miliseconds at a time? Yes! Will they look like a strobe in the middle of the day? Nope, unless you are looking directly at them. Also keep in mind that a lot of LED's are a bit on the directional side. Unless you start using a cree LED for each strobe, a lot of the LED's get their rediculous MCD ratings with very directional lenses. So ya, it puts out 110,000MCD as long as your standing in the 7 degree field of view.


Reply
dirknerkle
Posts: 10311
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
ChiefWarrant wrote:That was the thread that got me thinking about LEDS fro strobes. MY intent would be to run these off a DCSSR, as there are not any plans for me to build a REN48LSD this year.

So as Dirk said above, the LM317 is in there to protect the LED's

I took Brad's original idea and decided just to go ahead and us A/C current to power them instead of mess with using DC. I figured that low-voltage AC (24v) would also work with a normal SSR and I didn't need a special board or DC ssr for it. It worked great and was one of the best elements of my display last year. Here's a link...

http://doityourselfchristmas.com/forums/showthread.php?12021-A-C-Led-Strobes&p=121695#post121695


Reply
ChiefWarrant
Posts: 570
Topic starter
(@chiefwarrant)
Honorable Member
Joined: 19 years ago
dirknerkle wrote:I took Brad's original idea and decided just to go ahead and us A/C current to power them instead of mess with using DC. I figured that low-voltage AC (24v) would also work with a normal SSR and I didn't need a special board or DC ssr for it. It worked great and was one of the best elements of my display last year. Here's a link...

http://doityourselfchristmas.com/forums/showthread.php?12021-A-C-Led-Strobes&p=121695#post121695

Dave,
I saw that post and am thinking along the same lines...minus the wireless for now. I saw the SSR8 in the file library and I am schememing an SSR12 or SSR6 for the "Simple Ren24-SSR6" Mac did up. I was "thinking" that I could drive an SSR that way, but had not done the research on it yet.

In your "A/C Led Strobes" thread, is the LED portion is the same "circuit.pdf" ( http://doityourselfchristmas.com/forums/attachment.php?attachmentid=6576&d=1271070676 ) HelenaGuy talks about above?

In theory, I should be able to take your design and just attach the LED modules to an SSR powered by a 12VAC Wallwart.

You wouldn't happen to have an Express PCB file for the LED module? I saw the hand drawn diagram Brad Jones did and guess I just need a little clarification on some items…is the resistor in your photo the 9.1 Ohm resistor in Brad’s drawing?


Reply
dirknerkle
Posts: 10311
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
ChiefWarrant wrote:Dave,
I saw that post and am thinking along the same lines...minus the wireless for now. I saw the SSR8 in the file library and I am schememing an SSR12 or SSR6 for the "Simple Ren24-SSR6" Mac did up. I was "thinking" that I could drive an SSR that way, but had not done the research on it yet.

In your "A/C Led Strobes" thread, is the LED portion is the same "circuit.pdf" ( http://doityourselfchristmas.com/forums/attachment.php?attachmentid=6576&d=1271070676 ) HelenaGuy talks about above?

In theory, I should be able to take your design and just attach the LED modules to an SSR powered by a 12VAC Wallwart.

You wouldn't happen to have an Express PCB file for the LED module? I saw the hand drawn diagram Brad Jones did and guess I just need a little clarification on some items…is the resistor in your photo the 9.1 Ohm resistor in Brad’s drawing?

I'm sure I have the PCB file for my strobe module itself -- Brad used heat sinks on the LM317 too, but I didn't. As an experiment I found I could also dim them, and leave them on continuously yet they didn't burn out, so empirical testing indicated to me that a heat sink wasn't necessary. YMMV... When I get home tonite I'll pull up that PCB and repost it here. On the resistor, I think I did use a 9 ohm 1/4W but I can't remember. Geezer age has its benefits... 😆

The gate value of of the SSR's triacs will determine whether a 12vac wall wart will work for you. I used a 24v transformer (I think... that geezer thing goin' on again...) and it worked fine. And I've bought triacs of various kinds and values in bulk off eBay that are probably all over the lot in their quality of control but I've never encountered a problem. More later...


Reply
dirknerkle
Posts: 10311
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

Here's the schematic and PCB layout for the led strobes I made last year. My notes show that I used an 8-ohm resistor with it along with a 1N4001 diode. I was in error about supplying 24vac -- I looked at the controller and I used only a 12vac wall wart to power the whole shebang. The triacs were equivalent to BTA08's. Here are a couple photos of a completed strobe, the whole controller, too. The PCB file is in ExpressPCB format and it made 15 strobe circuitboards on one 4x6 piece of copper clad.

Hope this helps.


Reply
ChiefWarrant
Posts: 570
Topic starter
(@chiefwarrant)
Honorable Member
Joined: 19 years ago

Thank you Dirk,

I have 1N4001's and some 10 Ohm resistors on hand. I am going to hit the Shack and get some LM317's to start fabing some of these to test with the SSR12's


Reply
Page 1 / 2
Share: