LED string repair
 
Notifications
Clear all

LED string repair

13 Posts
6 Users
0 Reactions
4,109 Views
Posts: 1763
Topic starter
(@santacarl)
Noble Member
Joined: 19 years ago
[#28783]

Hi all.....

OK....I'm getting tired of throwing away $20.00 strings of LEDs because of what I suspect as being the cause of failure......either the diode or resister in the little canister....I think it's the reverse limiter......

I can deal with the occasional LED being out.....just splice in another one....

I'm trying to figure out how to effect repairs when the entire string is out.... Example...A string of 70 blue M5's.....the whole string is out.....using my LED keeper tool I CAN light up the entire string...so all the LEDs work.....fuses are good with no corrosion......has to be either the resistor or diode in the little 'bump' on the string.....

Since a semi conductor is usually more likely to be an issue than an resistor I'm figuring the diode is bad.....

All that to get to this question...... Does anyone know what type of diode this would be? Is it similar to a 1N-4001 or WHAT?

If I can get at it and replace it I can then worry about re-waterproofing......

This seems to be my biggest problem with LEDs....(and blue's seem much more problematic to me than other colors....but that's another topic for another time) this nonsense that they basically last forever is a joke....the individual LEDs are pretty hearty but the supporting circuitry seems to be a HUGE problem.... This year alone I've had to replace 4 strings.....these stringers are all less than 3 years old and due tot he blinky flashy nature of my show none of these strings has more than 100 hours total on time..... This is unacceptable....heck I got this kind of on time from my old incandescent's.....

Thanks


12 Replies
Posts: 350
(@kmalsom)
Reputable Member
Joined: 14 years ago

Are these full wave or half wave strings? You can cut out the blob entirely and calculate the appropriate resistors to put into the string and also add a full wave rectifier if you want to.


Reply
Posts: 1763
Topic starter
(@santacarl)
Noble Member
Joined: 19 years ago
kmalsom wrote:Are these full wave or half wave strings? You can cut out the blob entirely and calculate the appropriate resistors to put into the string and also add a full wave rectifier if you want to.

The current string I'm working on is half wave.....but I also have had similar issues with full waves....

If I cut out the blob and add resistance I still need some form of rectifier......Correct?

What's the calculation for resisters....and do you happen to have a part # on the full wave rectifier?

Thanks for the response..... I knew there had to be a way around this....


Reply
Posts: 350
(@kmalsom)
Reputable Member
Joined: 14 years ago

Here is the original post I used: http://doityourselfchristmas.com/forums/showthread.php?24777-Cutting-LED-Light-Strands&p=250572#post250572
Based on that we ran a group buy on a full wave converter board: http://doityourselfchristmas.com/forums/showthread.php?28751-Group-Buy-FWC-Full-Wave-Converter-1-2-to-Full-Wave-LED-string-Converter-board We will run another after the new year. or you can use a full wave rectifier available form Radio Shack or Mouser (sorry don't have a part number handy).
I built a calculator to determine resistor values: http://doityourselfchristmas.com/forums/showthread.php?28940-LED-String-Shortening-Resistor-Calculator


Reply
Posts: 350
(@kmalsom)
Reputable Member
Joined: 14 years ago
Santacarl wrote:If I cut out the blob and add resistance I still need some form of rectifier......Correct?

I have strings without a blob, I haven't checked, but I believe they just have a single diode in them.


Reply
Posts: 1763
Topic starter
(@santacarl)
Noble Member
Joined: 19 years ago
kmalsom wrote:I have strings without a blob, I haven't checked, but I believe they just have a single diode in them.

Yeah....I think that would make them a half wave.....question is what kind of diode is it.....


Reply
Posts: 1763
Topic starter
(@santacarl)
Noble Member
Joined: 19 years ago

Great....thanks for the response..... I'll keep an eye out for the group but.....any idea of timeframe?

It would be great to have a stash of repair parts.....this disposable string approach gets expensive...

kmalsom wrote:Here is the original post I used: http://doityourselfchristmas.com/forums/showthread.php?24777-Cutting-LED-Light-Strands&p=250572#post250572
Based on that we ran a group buy on a full wave converter board: http://doityourselfchristmas.com/forums/showthread.php?28751-Group-Buy-FWC-Full-Wave-Converter-1-2-to-Full-Wave-LED-string-Converter-board We will run another after the new year. or you can use a full wave rectifier available form Radio Shack or Mouser (sorry don't have a part number handy).
I built a calculator to determine resistor values: http://doityourselfchristmas.com/forums/showthread.php?28940-LED-String-Shortening-Resistor-Calculator

Reply
CaptKirk
Posts: 2200
(@captkirk)
Noble Member
Joined: 16 years ago
Santacarl wrote:Yeah....I think that would make them a half wave.....question is what kind of diode is it.....

Most use a 1N4004 or higher (to get enough margin on reverse voltage above the 110v or 22v swing). A 1n4001 is better for rectifying voltages AFTER a step down transformer.


Reply
Posts: 1763
Topic starter
(@santacarl)
Noble Member
Joined: 19 years ago
CaptKirk wrote:Most use a 1N4004 or higher (to get enough margin on reverse voltage above the 110v or 22v swing). A 1n4001 is better for rectifying voltages AFTER a step down transformer.

Ahhhh, there we go.....thanks....but I thought Scotty was the engineering genius! :biggrin:


Reply
Posts: 350
(@kmalsom)
Reputable Member
Joined: 14 years ago
Santacarl wrote:Great....thanks for the response..... I'll keep an eye out for the group but.....any idea of timeframe?

It would be great to have a stash of repair parts.....this disposable string approach gets expensive...

After the first of the year sometime. I want to make some minor changes to the board. I'm also working on seeing how to further smooth the lights and add the capability to add resistors into the same board.


Reply
Page 1 / 2
Share: