Help, Problem with ...
 
Notifications
Clear all

Help, Problem with LED flashing

23 Posts
3 Users
0 Reactions
8,702 Views
Posts: 14
Topic starter
(@wwilliams)
Active Member
Joined: 6 years ago
[#53282]

Hello I’m having some frustration with my Led ws2811 12 v string and ESP8266 NodeMCU ESP-12E CP2102 . I get a flash on my lights every few seconds. If I disconnect my data wire the lights don’t flicker/flash. I have tried different wires, soldered connections. Currently the data wire is 4 inches. As it gets longer the flashing increases. Any thoughts?

Sent from my iPhone using Tapatalk


22 Replies
MartinMueller2003
Posts: 7615
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

You are running data and V- together from the controller to the string? It sounds like you are getting noise on your data line. Any electrical devices nearby?


Reply
Posts: 14
Topic starter
(@wwilliams)
Active Member
Joined: 6 years ago

Thanks! based on your question I’m going to say this setup isn’t good.

Not only is my 12volt nearby but also 12v to 5v step down converter.

I did have these separated by ~3 inches but can try further.
I will separate by a foot or two and see if that helps.

Sent from my iPhone using Tapatalk


Reply
MartinMueller2003
Posts: 7615
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

what are you using as a level shifter?


Reply
Posts: 14
Topic starter
(@wwilliams)
Active Member
Joined: 6 years ago
MartinMueller2003 wrote:what are you using as a level shifter?

What is a level shifter? I only have on level of the house (200 led) currently if that’s what you mean

Sent from my iPhone using Tapatalk


Reply
MartinMueller2003
Posts: 7615
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

the output of that device is 3.3v. the pixels want 5v. a buffer / level shifter is used to do that.


Reply
Posts: 14
Topic starter
(@wwilliams)
Active Member
Joined: 6 years ago

Oh boy. Nope don’t have that. I see they are pretty cheap I will put that in my shopping list! I think it’s time to get a bread board too.

Sent from my iPhone using Tapatalk


Reply
Posts: 464
(@holtm)
Honorable Member
Joined: 19 years ago

RobG's "Buffer/line driver - null pixel without pixel "work really well as a level shifter on these boards. If you don't have one http://doityourselfchristmas.com/forums/showthread.php?47393-Buffer-line-driver-null-pixel-without-pixel/page22


Reply
Posts: 14
Topic starter
(@wwilliams)
Active Member
Joined: 6 years ago

Hello thank you all. With the null pixel suggestion, I cut two off LED of the end and wired them just after my nodemcu but before the 3 feet line connecting to my first string(I didn’t turn them off), I also included a Ferrite bead I had laying around. I’m have only seen a flash once since.

I may still put a buffer/level shifter.
Thanks everyone

And thanks for the driveway pep talk! northernwarrior

Sent from my iPhone using Tapatalk


Reply
Posts: 14
Topic starter
(@wwilliams)
Active Member
Joined: 6 years ago

So I did end up getting a little flashing after all. Today I upgraded to a bigger power supply and now I get massive flashing. I don’t know what to do next. I must be doing something wrong!

Sent from my iPhone using Tapatalk


Reply
Page 1 / 3
Share: