Help, Problem with ...
 
Notifications
Clear all

Help, Problem with LED flashing

23 Posts
3 Users
0 Reactions
8,701 Views
Posts: 14
Topic starter
(@wwilliams)
Active Member
Joined: 6 years ago
MikeKrebs wrote:How far is the first pixel from the controller?
It is really hard to see how you wired your controller. Did you run V-ground from the controller along with data? And did you run ground (V-) from the power supply for the pixels also to the ground from the controller?

Hey Mike I am running the controller v- from the controller to the 12v/5v power converter. Should I be running this controller ground to 12v ground,bypassing the 12/5v converter?

Sent from my iPhone using Tapatalk


Reply
Posts: 14
Topic starter
(@wwilliams)
Active Member
Joined: 6 years ago

Okay. So looking at this again this year. I now realize I have been getting flashing when I use my 10a power supply but not the 5amp.
Then realized my power converter is only 5a.

Does that make sense, the converter is causing the issue?

Im a little gun shy at this point so advice would be appreciated.

I plan to buy this to run my 10a power supply, unless there are better options

Thanks in advance

Cllena DC 12V 24V Step Down to 5V 10A 50W Converter Voltage Regulator, Waterproof DC/DC Buck Transformer Power Supply https://www.amazon.ca/dp/B07VGN39LS/ref=cm_sw_r_cp_api_glt_i_5PFPD5PW9NAK6NHH8ZWZ

Sent from my iPhone using Tapatalk


Reply
MartinMueller2003
Posts: 7615
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

At $26 each it is cheaper to use a full PSU to go from mains to 5v. My buck converters cost less than $4 each and do a fine job.


Reply
Posts: 14
Topic starter
(@wwilliams)
Active Member
Joined: 6 years ago

Thanks I have 12 volt strings, and of course need 5v on my esp8266 controller.

I will take a look for cheaper ones like you describe

Sent from my iPhone using Tapatalk


Reply
MartinMueller2003
Posts: 7615
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

Are you using the ESPixelstick V3 hardware? That has a built in voltage regulator to drop the 12v to the 5v and 3.3v needed by your show.


Reply
Posts: 14
Topic starter
(@wwilliams)
Active Member
Joined: 6 years ago

Nope not using that but I’m going to look into it, it would sure simplify my setup!
This is what I’m using

KeeYees Development Board WiFi WLAN Wireless Module for ESP8266 NodeMCU ESP-12E CP2102 Compatible with Arduino (3pcs) https://www.amazon.ca/dp/B07HF44GBT/ref=cm_sw_r_cp_api_glt_i_EN38J35M7DA5C77J6F4A?_encoding=UTF8&psc=1

Sent from my iPhone using Tapatalk


Reply
MartinMueller2003
Posts: 7615
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

Those look like they would run the ESPixelStick software. But you are right, you need to provide your own 5v for it and your own output buffer / driver / level shifter.


Reply
Posts: 14
Topic starter
(@wwilliams)
Active Member
Joined: 6 years ago
MikeKrebs wrote:unless the buck is faulty, it should be fine for driving the controller. Are you getting 5v at the controller? Since it solves the problem...Any reason you don't want to use a dedicated psu to drive the controller?

I would need a 12v and 5v power supply in that case correct, and need to connect the grounds?

Sent from my iPhone using Tapatalk


Reply
Posts: 14
Topic starter
(@wwilliams)
Active Member
Joined: 6 years ago
MartinMueller2003 wrote:Those look like they would run the ESPixelStick software. But you are right, you need to provide your own 5v for it and your own output buffer / driver / level shifter.

Sent from my iPhone using Tapatalk


Reply
Posts: 14
Topic starter
(@wwilliams)
Active Member
Joined: 6 years ago
MartinMueller2003 wrote:Those look like they would run the ESPixelStick software. But you are right, you need to provide your own 5v for it and your own output buffer / driver / level shifter.

I’m just using a sacrificial pixel. I’m not sure if that is providing buffer/driver/level shifter though.

Sent from my iPhone using Tapatalk


Reply
Page 2 / 3
Share: