Notifications
Clear all

help please

22 Posts
11 Users
0 Reactions
9,424 Views
Posts: 371
Topic starter
(@gebbinn)
Reputable Member
Joined: 16 years ago
[#16743]

I know next to nothing about creating circuits, so I am hoping you gents can help me. I have a plaster plaque of a mummy, that I drilled out the eyes and installed a couple of LED lights to make him glow. They run on 5v. right now, they are set up with the 2 LEDs soldered together with a 330ohm resister on the positive side.

What I would like to do is make them flash. I have spare parts for the Renard SS series boards, as well as a bunch of parts from an electronics kit, so I am hoping to have the parts on hand, if not, and I need to, I can go to ratshack to purchase supplies. Would like to keep this down to <$10, preferrably <$5.

all I want is to make them flash. It would be great if I could vary the flash speed, but not neccessary.

Can anyone help me out here?


21 Replies
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

There are many examples available using 555 timers - just google for them - even RatShack has (or used to have) 555 timers - here's an example page - http://wild-bohemian.com/electronics/flasher.html


Reply
chelmuth
Posts: 1077
(@chelmuth)
Noble Member
Joined: 16 years ago

They still have 555 timers.. they are in the purple drawer.. that says IC's on it.. I'm thinking a 555 and a variable resistor..


Reply
Mactayl
Posts: 2491
Guest
(@mactayl)
Member
Joined: 17 years ago

Here is another one using a 555 timer that you can get at Shadio Rack

http://www.electrokits.com/LED-Circuits/Alternate-LED-Flashing


Reply
joeytx
Posts: 249
(@joeytx)
Reputable Member
Joined: 19 years ago

RS has a Bright-Red Blinking LED Module( http://www.radioshack.com/product/index.jsp?productId=2062571# ), and a LED that already blinks ( http://www.radioshack.com/product/index.jsp?productId=3060680 ). The blinking LED can drive a second LED in series.


Reply
klyneshouse
Posts: 230
(@klyneshouse)
Reputable Member
Joined: 16 years ago

I was goofing off last weekend with extra red leds to make "eyes in the bushes"-(no mummy, just sets of red eyes strung on cat5)
I based the simple circuit on the Fast using extra PIC16F688's i had on hand putting the (-) led on the pics outputs-
http://www.doityourselfchristmas.com/wiki/index.php?title=FAST_Finally_Affordable_Snowfall_Tube

The fast asm will work but also Pshort just posted a more easily modifyable asm just yesterday you can try.
http://doityourselfchristmas.com/forums/dynamics/showentry.php?e=161&catid=6

Best news is recycling the PIC at christmas will get you well under a few bucks for the whole thing.


Reply
Posts: 371
Topic starter
(@gebbinn)
Reputable Member
Joined: 16 years ago

So basically, if I use this diagram from the wiki

I could wire that up, and wire my leds to r1 on the - side, and say, r2 and r3 on the + side? Or is that backwards? and that would be a pic programmed with the asm from Pshort, correct?


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

THIS COMMENT IS ONLY RELEVANT IF YOU ARE USING THE BLINKER CODE THAT I'VE UPLOADED TO THE FILE LIBRARY.

First, you need a current limit resistor to go in series with each LED. The value of this resistor will depend on what color LEDs your are using.

Second, you need to make sure that the maximum current through all of the LEDs (added together) is less that the spec for the PIC16F688 (90 mA). This probably means that you can only use three or four outputs at once if you are drving them with 20 mA while connecting them directly to the PIC.

Third, if you are using the file that I uploaded without any changes, the anode of the LED must go to +5 and the cathode goes to the current limit resistor, and the other end of the current limit resistor goes to one of the relevant PIC output pins (pin 3, 7-13).

Fourth, if you want to drive more than 90 mA total, you'll need to add some booster transistors.

Sorry if this is description is a bit condensed...


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

Just took a look at the link you posted...this has nothing to do with FAST or LEDancer.


Reply
DIY Sparks
Posts: 240
(@diy-sparks)
Reputable Member
Joined: 16 years ago
Gebbinn wrote:I know next to nothing about creating circuits, so I am hoping you gents can help me. I have a plaster plaque of a mummy, that I drilled out the eyes and installed a couple of LED lights to make him glow. They run on 5v. right now, they are set up with the 2 LEDs soldered together with a 330ohm resister on the positive side.

What I would like to do is make them flash. I have spare parts for the Renard SS series boards, as well as a bunch of parts from an electronics kit, so I am hoping to have the parts on hand, if not, and I need to, I can go to ratshack to purchase supplies. Would like to keep this down to <$10, preferrably <$5.

all I want is to make them flash. It would be great if I could vary the flash speed, but not neccessary.

Can anyone help me out here?

Your post seems straightforward -flashing LEDs--- the responses confuse my primitive brain so maybe I'm missing something. I've got self-contained red flashing LEDs (about 4 or 5 handy; 5mm; 1Hz flash) that I'll send you gratis. PM me, unless I'm not getting the point.


Reply
Page 1 / 3
Share: