Im wondering if someone could help me since I'm a bit stuck, I want to control a 3W led. Ive worked with thousands of 5mm led's and I can work out how to power them fine its the 3W that confuse me haha.
Ive looked on the internet and there seems to be loads of different ways, some easy but creating alot of heat and others more complex. So whats the best way to do it? My led specs are:
Red - 2.5V ~ 3.0V, 350mA
Green - 3.2V ~ 3.8V, 350mA
Blue - 3.2V ~ 3.8V, 350mA
I would be using a 5V power supply. I will probably have a few but I want to be able to control them indivdually so they wont be wired together.
Thanks Steve 🙂
Are you sure these are considered 3W or 1W? Using the maximum specs, 3.8V x .35A = 1.33W - nowhere near 3W... I just received some of the "star" 1W LEDs and they use 300mA - I was thinking of making a small flood with them - not sure yet.
edit - - are these a combined RGB LED? That might explain the 3W spec if they are combining all three...
Anyway - to answer your question - how many of these do you have? If you have several of them, the Ren48LSD would work very well for this - it can drive 350mA at 5v with no problems. If you only have a couple, then there is Dirk's 8-channel wireless "LSD" board and I thnk there was a Renard Simple design from Mactayl using transistors as well.
I think there selling them as 3W but each colour is only 1W. I wasnt really sure how many I'm going to use but I'm going to control them using a SimpleRen32 and a DC SSR. So it will be controlled by transistors, the same as used on the ren48lsd, just a smaller version. I'm just stuck with the best way to power them since a resistor probably wont cut it here haha.
Steve
Not sure how may you are looking at controlling
Resistors are not a good option to power high current LEDs
A high current driver for up to 350ma that can be ganged up for even more current.
JOel
Do I want constant current or constant voltage? I'm new to this, I'm use to 3 resistors in series with a resistor haha. Any ideas of telling me what I need and how to do it or a link to what to do would be great.
Thanks 🙂
You "NEED" constant current with LED's such as these. LED's as a whole are constant current, but for 20mA you can "get away with" resistors. The 44 project is a great DMX based constant controller.
Just remember you'd need a dmx dongle to go that route.
You can find some constant current drivers that you could use with a Ren48LSD or as an add-on to a DC-SSR. The simplest being two transistors and a few resistors, all the way to integrated packages.
Take a look at this post regarding the 44 project controller and calculator, it may be what your looking for http://auschristmaslighting.com/forums/index.php/topic,1061.msg8816.html#new
Depending on how many you want, the 44 project at Dec1.org is an option, or you could use a standard controller with LM317's configured as Constant Current sources.
I would be looking to control the devices using something like a renard board, my plan is to etch the 32 channel one that was recently developed and use that and then control my DC devices using a transistor so I wouldnt need any DMX controllers just really a basic controller that I can connect to a transistor.
Steve
So then the 44 is out.
The problem with the LM317 is you need 3 volts of headroom for Constant Current mode.
Maybe something similar to what Matt is working on over here could be used:
http://doityourselfchristmas.com/forums/showthread.php?15804-Yet-Another-LED-Strip-PCB
