Helix Ether-Node Co...
 
Notifications
Clear all

Helix Ether-Node Controller

108 Posts
8 Users
0 Reactions
73.4 K Views
Posts: 373
(@blantrip)
Reputable Member
Joined: 16 years ago
Warlock wrote:Odd considering others have had it. Maybe that is the issue

The "board type" field is grayed out on mine as well and was also for last year's show so I don't think there is anything you can do regarding that. It was a good suggestion though.

I still don't have mine working and the frustration and stress level is getting pretty high on my part. Argghh!

The differences between last years show with my ether-node controller and this year are:

1) This year I used Vixen3 and exported to a Vixen 2.1 sequence. The V2.1 sequence looks fine, it plays in Vixen 2.1 and I can use HNS to upload the sequence to my Helix Main and Ether-Node boards without any errors. I just don't get any pixels flashing.
2) Added an additional E682 board.
3) Added MANY more pixels so the vixen sequence channel count is >4,000 where last years overall channel count was ~300.

I've uploaded last years show to my Helix equipment and that works, so I'm guessing it has something to do with either using Vixen3 or the increased channel count.

I'll try to do a smaller sequence in Vixen3 to see if that has an effect and I'll also try copying nutcracker effects into a vixen2.1 sequence to see if that works.

Either way it is taking too much time, energy and sapping any sanity I still have left but thanks for the various suggestions.

at kiowamike, good luck to you. how did you program your sequences? Straight in Vixen 2 or did you use Vixen3 also?


Reply
Posts: 947
(@warlock)
Noble Member
Joined: 19 years ago

The heartbeat led steady on means everything. If it is not flashing thn it is not rwcieving the dmx signal correctly. Then it has to be a programing issue with vixen or in the transfer between vixen and the HNS


Reply
Posts: 300
(@kiowamike)
Reputable Member
Joined: 18 years ago
Either way it is taking too much time, energy and sapping any sanity I still have left but thanks for the various suggestions.

Ditto.

at kiowamike, good luck to you. how did you program your sequences? Straight in Vixen 2 or did you use Vixen3 also?

Thanks, I appreciate it.
I made a test sequence in Vixen 2.1 that turns all channels on for 1 second then off for 1 second. Currently I am using a REN SS8 for testing before I move things outdoors. I am not running a full show this year as I do not have the time it takes to set up and maintain. I am just running a pixel mega tree and a few mini trees as an animated display (no sequencing and music). My E1.31 bridge is fully tested and ready to go. I have already invested time and money into the Helix controllers and would prefer them to work for me instead of spending more money on a wireless access point to go outside. Also my wife says no more wires through windows.


Reply
Posts: 300
(@kiowamike)
Reputable Member
Joined: 18 years ago
The heartbeat led steady on means everything. If it is not flashing thn it is not rwcieving the dmx signal correctly. Then it has to be a programing issue with vixen or in the transfer between vixen and the HNS

Thanks I'll make a new test sequence.


Reply
Posts: 947
(@warlock)
Noble Member
Joined: 19 years ago

The heart beat led has to flash off and on at a steady rate while working to show it is recieving signal. If it is solid on there should be an error file generated as to why. Use noyepad to open ypur error file and see. If there is no error file I'd check the sd card on your main board for an error file.


Reply
Page 14 / 22
Share: