I'm doing something...
 
Notifications
Clear all

I'm doing something wrong I guess....

30 Posts
8 Users
0 Reactions
9,661 Views
Posts: 34
Topic starter
(@rstetson)
Eminent Member
Joined: 18 years ago
[#5544]

I built my grinch and have external power to it, tested it at 5.09v on the grinch board and at the ssr's. I'm running 8 ssr's for a total of 32 channels. I get all of the led's to light up also. When I start to plug in lights to the ssr's I get 1 channel thats always on and none of the other channels do anything on each of the 8 ssr's. I added in the 595 plugin to my sequences also. I'm not trying to dim anything just off and on this year. What am I missing or just not doing thats causing the lights not to go blinky flashy?

Rick


29 Replies
Posts: 93
(@petefats)
Estimable Member
Joined: 19 years ago

Check to make sure you're 595's/triacs aren't installed backwards.


Reply
Posts: 34
Topic starter
(@rstetson)
Eminent Member
Joined: 18 years ago

Here are pics of how all of my ssr's look and my grinch. According to teh pics and directions I followed I believe they are in correctly. But at this point anything wouldn't surprise me..LOL

Rick


Reply
Posts: 485
(@sjwilson122)
Honorable Member
Joined: 19 years ago

check the com port settings and also check in Vixen, profile/manage/(select profile you are using)/output plugins (select the plugin you are using, this will then allow you to click on the plugin setup tab)/ in plugin setup make sure that it shows channel 1 to 32


Reply
Posts: 854
(@terbobob)
Noble Member
Joined: 19 years ago

Question - are you using patch cable or network ? ( patch - the wires are straight thru , network , they are not )
Am I correct , when I say that you stated that when you leave the GRINCH hooked to your PC , and NO ssr's , that the GRINCH's LED's light up correctly , and when you connect the SSR's to the GRINCH , that is when everything goes hay-wire ?


Reply
Posts: 339
(@dan-ross)
Reputable Member
Joined: 19 years ago

Check your LPT port settings in your bios to see if it's set to EPP if it is try the other settings, if not change it to it. Set your 595 plugin to 64 channels even though you are only using 32 your grinch has 64. Did you try connecting a jumper from the ground of your power supply to your PC? The last thing I can think of is the voltage from you LPT port is to low, if you can lower your supply voltage this would help if not you can try this http://www.doityourselfchristmas.com/forums/showthread.php?t=5648


Reply
Posts: 34
Topic starter
(@rstetson)
Eminent Member
Joined: 18 years ago

There are two different 595 plugins. I'm using the 595 simple. Is that correct fo rjust basic on and off lights. In that plugin setup it asks for ports. I'm using the same one as in my bios port 378.

When I plug the Grinch into the pc the led lights up. Then when I plug the ssr's into the Grich the led on them light. Everything is working fine to that point from what I can tell. Wehn I add in lights I get only 1 channel come on and its always channel 4.

Dan I knew I had to switch the LPT settings and couldn't find exactly what it was until you made your post. Thats now changed, but it didn't change anything. Now I'm going to follow that link you posted in your last reply and see what happens from there.

Rick


Reply
Posts: 34
Topic starter
(@rstetson)
Eminent Member
Joined: 18 years ago

Here is something interesting. When I turned everything off awhile ago I just went back to try something else. None of the mimi lights came on. Then after a few min channel 4 came on and after about 5 min went out and then another 5 min they came back on. When they come on its all the way with no blinking either both times.

Rick


Reply
Posts: 34
Topic starter
(@rstetson)
Eminent Member
Joined: 18 years ago

Ok connected the ground wire to my pc and still the same results. Now I'm really lost and frustrated!!

Rick


Reply
Posts: 94
(@seahocaptain)
Estimable Member
Joined: 18 years ago
RStetson wrote:There are two different 595 plugins. I'm using the 595 simple. Is that correct fo rjust basic on and off lights. In that plugin setup it asks for ports. I'm using the same one as in my bios port 378.

When I plug the Grinch into the pc the led lights up. Then when I plug the ssr's into the Grich the led on them light. Everything is working fine to that point from what I can tell. Wehn I add in lights I get only 1 channel come on and its always channel 4.

Dan I knew I had to switch the LPT settings and couldn't find exactly what it was until you made your post. Thats now changed, but it didn't change anything. Now I'm going to follow that link you posted in your last reply and see what happens from there.

Rick

Not sure if it makes a difference but arent you suppose to use the Olsen 595 plugin for the Grinch? Thats what I'm using and it seems to work fine.

David


Reply
Page 1 / 3
Share: