cannot get channels...
 
Notifications
Clear all

cannot get channels to fire correctly

12 Posts
8 Users
0 Reactions
4,590 Views
Posts: 7
Topic starter
(@trevorgreen)
Active Member
Joined: 19 years ago
[#5560]

I am using a grinch board and vixen v2. I seem to have a problem in that when I want to turn channel 1 on it will not turn on unless I also turn channel 2 on. Likewise for channel 2. I need to turn on channel 3 as well as channel 2 to turn on channel 2. It ooks like if I want to turn channel x on I have to turn channel (x+1) on as well to make channel x work. I am using standard olsen 595 plugin. It is driving me crazy, can someone help me please?


11 Replies
NogginBoink
Posts: 482
(@nogginboink)
Honorable Member
Joined: 19 years ago

That does indeed sound odd. Can you tell us how you tested this and arrived at this conclusion? Perhaps you're misinterpreting some of the information you've gathered?


Reply
Posts: 18
 ulto
(@ulto)
Eminent Member
Joined: 18 years ago

This is the exact problem I am having.


Reply
Posts: 7
Topic starter
(@trevorgreen)
Active Member
Joined: 19 years ago

I just have a simple test tool with led's. When I plug it into any port and then test the channel, I have to activate both the channel it is connected to and the next channel for the led to light up. it is just odd, I have checked everything and cannot find where the problem lies.


Reply
Posts: 152
 ibby
(@ibby)
Estimable Member
Joined: 19 years ago

How are you powering you grinch? Do you have a common ground between the Grinch and the PC. I have found this to help.

Also how about changing the chip 4 with chip 1 and see if you have a bad chip.

Ibby


Reply
toodle_pipsky
Posts: 1285
(@toodle-pipsky)
Noble Member
Joined: 19 years ago

Sounds like a similar problem I had months ago trying to get a Ren-C/Grinch combo to work. I'll have a dig and see what the deal was. However if you have just a Grinch having that problem, the info may be irrelevant. Tell me, is it just a Grinch you are running?


Reply
Posts: 1079
(@bmcgeeny)
Noble Member
Joined: 18 years ago
trevorgreen wrote:I am using a grinch board and vixen v2. I seem to have a problem in that when I want to turn channel 1 on it will not turn on unless I also turn channel 2 on. Likewise for channel 2. I need to turn on channel 3 as well as channel 2 to turn on channel 2. It ooks like if I want to turn channel x on I have to turn channel (x+1) on as well to make channel x work. I am using standard olsen 595 plugin. It is driving me crazy, can someone help me please?

Sounds like a cableing problem. May be ground.
If you have no ground and you turn channel one on, nothing will happen. Turn channel 2 on and it acts like a ground for channel 1 and comes on.

Other possibility I had was the data voltage is too low to trigger your chip.

Alegro or MBI?

The Allegro's are much more sensitive.


Reply
Posts: 7
Topic starter
(@trevorgreen)
Active Member
Joined: 19 years ago

thanks for all the advice. I thought about ground but it all looks correctly wired. I am using MBI's. I am powering the grinch from an old PC ATX power supply.


Reply
Posts: 7
Topic starter
(@trevorgreen)
Active Member
Joined: 19 years ago
ibby wrote:How are you powering you grinch? Do you have a common ground between the Grinch and the PC. I have found this to help.

Also how about changing the chip 4 with chip 1 and see if you have a bad chip.

Ibby

I replaced the chips. However, the problem happens on all ports so it is irrelevant which chip is being used. I will try the common ground, but I am using a laptop so it may be difficult.

thanks


Reply
Virtus
Posts: 1182
(@virtus)
Noble Member
Joined: 19 years ago

Can you turn ON channel 4 if channel 1 is ON? Do they have to be sequential or is that all you have tried? What about channel 16 to 17 when the output spans chips?


Reply
Page 1 / 2
Share: