Grinch & RenC Quest...
 
Notifications
Clear all

Grinch & RenC Question

8 Posts
5 Users
0 Reactions
3,353 Views
Posts: 13
Topic starter
(@rdwizard)
Eminent Member
Joined: 18 years ago
[#5256]

I have 2 Grinch controllers and one completed RenC. I am hooked up to my computer serial port to the RenC then to the Grinch. I have removed the Out going ethernet cable from the Grinch to RenC to eliminate my flickering problem. My question is this:

Can I hook up my Second Grinch to the output of the first Grinch, assuming that I do not try to dim on the second Grinch controller channels? I am assuming that the signal out from the first Grinch is now in the proper format for the second Grinch minus the fact that I won't be able to dim. Can anyone verify this will work before I try it and fry my controllers?


7 Replies
RichF
Posts: 1356
(@richf)
Noble Member
Joined: 19 years ago

You must have a ren-c for each grinch.


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

It shouldn't fry, but it won't do what you want either.


Reply
RavingLunatic
Posts: 1502
(@ravinglunatic)
Noble Member
Joined: 19 years ago
RDWizard wrote:I have 2 Grinch controllers and one completed RenC. I am hooked up to my computer serial port to the RenC then to the Grinch. I have removed the Out going ethernet cable from the Grinch to RenC to eliminate my flickering problem. My question is this:

Can I hook up my Second Grinch to the output of the first Grinch, assuming that I do not try to dim on the second Grinch controller channels? I am assuming that the signal out from the first Grinch is now in the proper format for the second Grinch minus the fact that I won't be able to dim. Can anyone verify this will work before I try it and fry my controllers?

You should never assume anything around here!

A Ren-C only outputs 64 channels of data for the Grinch/Olsen that is connected to it. So you cannot run the output of the first Grinch to anything else except back to the Ren-C for PWM support.


Reply
Posts: 13
Topic starter
(@rdwizard)
Eminent Member
Joined: 18 years ago

RavingLunatic-
If the RenC- only puts out 64 channels of data to drive the Grinch that is connected to it, then how does the next RenC daisychained to the first one get anything to work with? Is the second 64 channels filtered on the RenC then passed on to the second RenC?


Reply
RavingLunatic
Posts: 1502
(@ravinglunatic)
Noble Member
Joined: 19 years ago

You got me on that.

Yes, the Ren-C repeats/sends all remaining data (after the 64 channels it needs) out the RS OUT connector. But that data is still in serial (Renard protocol) format which can only be used by other Ren-Cs or Renard systems.


Reply
dnesci
Posts: 563
(@dnesci)
Honorable Member
Joined: 19 years ago

To use your non-dimming Grinch, it must be connected to the parallel port, using the 595/Grinch Plug-In. Set the output channels on this plugin to channels 65-128.


Reply
Posts: 13
Topic starter
(@rdwizard)
Eminent Member
Joined: 18 years ago

I was trying to take a short cut because I don't have a parallel port on my computer. I am using a USB->Serial dongle. I was going to use my second grinch to fire 64 strobe leds. I will reconfigure for next year.


Reply
Share: