Flickering DC light...
 
Notifications
Clear all

Flickering DC lights

22 Posts
8 Users
0 Reactions
13.7 K Views
Posts: 393
Topic starter
(@soakes94)
Honorable Member
Joined: 18 years ago
[#12183]

Hey, so to explain my problem when I use LED DC lights they flicker when dimmed or wrong channels will flicker so maybe lets say I'm dimming channel 18 channel 4 will flicker. I'm using a ren-c with a H11A11 with a 24VAC supply power source, I'm not sure what version is on my PIC and I sent wjohn a message but haven't heard back.

I don't have any PIC programming equipment so I cant check myself or re-program the chip. I'm in the UK but I don't know if this would make any difference since I'm using DC and not AC, my AC lights seem to dim fine.

Does anyone have any ideas what I should do? If its a PIC issue there isn't much I can do so I will just have to put up with it lol

Thanks 🙂


21 Replies
Posts: 1041
(@christmas-light)
Noble Member
Joined: 18 years ago

Are you using AC ssr or DC ssr ?


Reply
Posts: 393
Topic starter
(@soakes94)
Honorable Member
Joined: 18 years ago

DC SSR for my DC lights and AC SSR for my AC lights


Reply
LabRat
Posts: 2981
(@labrat)
Famed Member
Joined: 17 years ago

Power cables running in close proximity to the control cables to the SSR's?

(I'm in a similar pickle. Had a lot of "mis-firing" in my display last year. I haven't tracked it down yet.. but I'm assuming interference from the power lines in the control lines was causing it).


Reply
Posts: 393
Topic starter
(@soakes94)
Honorable Member
Joined: 18 years ago

If it is that it's of a difficult one to avoid though I would think, I struggle enough just to get things to plug in never mind them organizing everything lol


Reply
Posts: 1041
(@christmas-light)
Noble Member
Joined: 18 years ago
LabRat wrote:Power cables running in close proximity to the control cables to the SSR's?

(I'm in a similar pickle. Had a lot of "mis-firing" in my display last year. I haven't tracked it down yet.. but I'm assuming interference from the power lines in the control lines was causing it).

Can that have a effect on flickering ?

Maybe that was why my 3 ren 24 controllers was making some strange things ?


Reply
ErnieHorning
Posts: 4434
(@erniehorning)
Famed Member
Joined: 19 years ago

I can't see power getting into the communication line unless theres some kind of inductive noise but some LOR users clain they have experianced problems with just lights.

With AC, I can see problems if there is a lot of noise on the power cord going to your controller. The zero crossing would detect the noise if it crossed through zero. Very long power cords coould also phase shift the current and make the zero crossing circuit see zero at the wrong time.

This is the same reason that LED string sometimes need an additional resistive load so the TRIAC's will trigger correctly.

If you susspect that the power line is causing problems, try adding resistance to that cord (ie. adding incandescent bulbs).


Reply
Posts: 1041
(@christmas-light)
Noble Member
Joined: 18 years ago
ErnieHorning wrote:

If you susspect that the power line is causing problems, try adding resistance to that cord (ie. adding incandescent bulbs).

Me ?

No I have fixed the problem with adding a full wave rectifier before the ren 24 (ac to the transformer and "DC" to the traice 🙂 )


Reply
Posts: 556
 jpb
(@jpb)
Honorable Member
Joined: 19 years ago

Stephen,

I have bought a second RENC Grinch combo for this year and when I tested it, it had the flickering problem.

I made the hardware change to the the RENC that I made to my other one as per
http://doityourselfchristmas.com/forums/showthread.php?t=7044&page=10 post 98 and it fixed the flickering problem.

I did not make any change to the firmware in the PIC and don't know what is in it except that it came pre-programmed from WJohn. I suggest you try the change that I made as it is easily reversed.

Jon


Reply
Posts: 393
Topic starter
(@soakes94)
Honorable Member
Joined: 18 years ago

I will give it a go, my workshop/shed is currently covered with the inside of a computer since it broke and I decided to take it all apart and then realized after removing the heat-sink I didn't have any heat compound and I think that the CPU might be overheating lol. I ordered some though and it should be here soon :). I hope i can get the computer working as well as without there will be no blinky flashy as its the vixen computer lol


Reply
Page 1 / 3
Share: