I am having several channels flickering on and off during the running of some channels. These channels are all on the 4th pic on the grinch. Any thoughts or suggestions? When I got the pics 3 years ago they were already flashed for me. So reflashing isn't an option unless I buy stuff to do that if that is the problem. Any help would be greatly appreciated.
I am ruining grinch with ren-c and a zc.
Chris
Hmmm..... either of the chips used in the Grinch are not programmable so the programming could only be on the 16F627A chip in the Ren-C. It's possible it could need reflashing. None of them would work if there was no ZC so that's likely not the issue. Have you experimented with swapping chips with the 4th chip to see if the problem follows that chip? If so, simply replace the chip and the problem should be solved.
I have tried other channels and it seems to move around. When ssr 1 is on for Channel's 1-4 it appears on ch 44,48 when ssr 4 is on and 16-20 are on it could be on ch 5-8. It's very random.
Planker, have you found your problem yet? I too have a Grinch set up that I have been running 40 channels from for the past three or 4 years without any issues. This year I decided to add the remaining 24 available channels (to get the 64 max from one Grinch) and none of the new ones worked properly. I swapped the chips with brand new ones, even swapped with the three verified working ones from the past few years and same issue. I'm getting random blinking as well as other channels are bleeding into the new ones. Example: the new channels are for say arches and hey are getting sequencing from the mega tree ( say for instance new channel 41-44 get sequencing from channels 20-24 or similar) Are you getting this type of activity? I also wonder if it has to do with the way my parallel port is configured. I tried the ssrs on different channels and those are all working fine, it has something to do with the last chip on the Grinch...
Yes same thing. This year I added the last chip to have the last 16 ch and now Thant is identical to what I have going on. I've swapped ssr no luck. Moved pics no luck. Reseated everything and nothing. Show runs fine if I pull the last pic on grinch. Even if I swap it with one of the others it still does it. Hopefully someone will have some insight.
Have you made sure that you updated your sequence and plug-in for 64 channels????
The Grinch will just shift over data unto the last chip whether it is the correct data or left over data from the previous event interval.
Could be a voltage issue - My Grinch was very picky about the voltage.
When running it with exactly 5V I had flicker and random channels all over the place - It ran best with around 4.6 V.
Odd thing is I never had the issue till I added that 4th pic. I had the prob before when I had it I but wasn't using it and removing it helped.
I have had this problem and have solved with some help from others. This is an extract from an old thread
Earlier this year when I built my REC-C I had a problem with ghosting of channels using a Grinch. For example I would turn on Channel 12 and Channel 42 would start to flicker.
In the end I reflashed the chips to the latest firmware and cut a track on the REN-C and soldered a wire in. The hardware changes are documented in the asm file.
;; "This change requires a h/w change to the board - disconnect the ZC
;; signal from pin 2 of the HC02, and connect pin 2 of the HC02 to pins
;; 11,12 of the PIC.
The way I did it was easy to do and easy to reverse. See my post on the 29th of June in this thread. It even has photos
http://doityourselfchristmas.com/for...t=7044&page=10
Jon
jpb wrote:I have had this problem and have solved with some help from others. This is an extract from an old threadEarlier this year when I built my REC-C I had a problem with ghosting of channels using a Grinch. For example I would turn on Channel 12 and Channel 42 would start to flicker.
In the end I reflashed the chips to the latest firmware and cut a track on the REN-C and soldered a wire in. The hardware changes are documented in the asm file.
;; "This change requires a h/w change to the board - disconnect the ZC
;; signal from pin 2 of the HC02, and connect pin 2 of the HC02 to pins
;; 11,12 of the PIC.The way I did it was easy to do and easy to reverse. See my post on the 29th of June in this thread. It even has photos
http://doityourselfchristmas.com/for...t=7044&page=10Jon
Ditto to that. I had 2 Ren-C's running and that fix eliminated the flickers and ghosting also.

