Express pcb format ...
 
Notifications
Clear all

Express pcb format schematic

4 Posts
3 Users
0 Reactions
5,910 Views
Posts: 20
Topic starter
(@mike-v-florida)
Eminent Member
Joined: 16 years ago
[#13082]

First I have to admit that I have not yet read all 14 pages of this section of the forum, so if the answer to my question is there I'm sorry.

I'm looking for the schematic for the grinch in the "sch" format.

Here is why, I have an ond ethernet hub box that has provisions for 16 RJ45's in the front, several holes in the back doe plugs and even has a 5 volt supply in it. I need to redesign the board and was hoping to save time by using the schematic to make the board layout and not have to recreate all the components.

Can anyone help?


3 Replies
dirknerkle
Posts: 10309
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

Welcome to DIYC, Mike - and Happy Thanksgiving, too!

Some of the files in the File Library are in ExpressPCB format, while others may be in other formats for different pieces of software, such as Eagle, DesignSpark, or what-have-you. In most cases, the person who posted the file posted it in the format they typically use either all or most of the time.

ExpressPCB, for example, is a free program that is actually quite easy to use, and is very good if you home-etch your own boards. It's not so good if you plan to send them out to a board house because their format is proprietary and very few board makers will accept their files -- except for ExpressPCB, of course! They're not horribly expensive, but they're not cheap, either. And they do provide excellent quality, so it's not a bad way to go.

Eagle is also a free download, and has more options than ExpressPCB. Many of the others also produce Gerber files and so forth.

Not every board will have an electrical schematic layout available, although many do. If it isn't available, you'd have to take the PCB layout tracing and produce it on your own by discerning the various board tracings, a sort of reverse-engineering process. Not everyone is a electronic guru and makes a board from a schematic; sometimes they skip the schematic and go right to the PCB layout. However, the Grinch is a pretty simple board -- very few components, and most of the pins on the Grinch's chips go to channel signal control, so it shouldn't be very hard to do.

The Grinch, by the way, is losing in popularity even though it's a relatively inexpensive board to make. One problem is that it usually uses a parallel output from the computer and computer manufacturers are increasingly going to USB outputs instead of using parallel. Another issue is the availability of either the Allegro or the MBI chips -- they're getting scarce. And lastly, it's primarily an on/off kind of control unless you use a DMX or Ren-C adapter with it, which then enables it to have dimming capability. Using either DMX or Renard eliminates the issue with the parallel port however, and there are plenty of options to control the Grinch that way via serial or USB adapter.

Again, welcome to DIYC!


Reply
Posts: 52
(@timsdailydose)
Trusted Member
Joined: 18 years ago

Mike, the Schematic for the Grinch can be found at this link. It is the first post on this forum page from WJohn.

http://www.doityourselfchristmas.com/forums/showthread.php?t=126


Reply
Posts: 20
Topic starter
(@mike-v-florida)
Eminent Member
Joined: 16 years ago
dirknerkle wrote:Welcome to DIYC, Mike - and Happy Thanksgiving, too!

Some of the files in the File Library are in ExpressPCB format, while others may be in other formats for different pieces of software, such as Eagle, DesignSpark, or what-have-you. In most cases, the person who posted the file posted it in the format they typically use either all or most of the time.

ExpressPCB, for example, is a free program that is actually quite easy to use, and is very good if you home-etch your own boards. It's not so good if you plan to send them out to a board house because their format is proprietary and very few board makers will accept their files -- except for ExpressPCB, of course! They're not horribly expensive, but they're not cheap, either. And they do provide excellent quality, so it's not a bad way to go.

Eagle is also a free download, and has more options than ExpressPCB. Many of the others also produce Gerber files and so forth.

Not every board will have an electrical schematic layout available, although many do. If it isn't available, you'd have to take the PCB layout tracing and produce it on your own by discerning the various board tracings, a sort of reverse-engineering process. Not everyone is a electronic guru and makes a board from a schematic; sometimes they skip the schematic and go right to the PCB layout. However, the Grinch is a pretty simple board -- very few components, and most of the pins on the Grinch's chips go to channel signal control, so it shouldn't be very hard to do.

The Grinch, by the way, is losing in popularity even though it's a relatively inexpensive board to make. One problem is that it usually uses a parallel output from the computer and computer manufacturers are increasingly going to USB outputs instead of using parallel. Another issue is the availability of either the Allegro or the MBI chips -- they're getting scarce. And lastly, it's primarily an on/off kind of control unless you use a DMX or Ren-C adapter with it, which then enables it to have dimming capability. Using either DMX or Renard eliminates the issue with the parallel port however, and there are plenty of options to control the Grinch that way via serial or USB adapter.

Again, welcome to DIYC!

Thank you for your reply.

While I understand the move to dimming, I think on and off will be fine for me for the forseable future. As for the Parallel port, I have a lap top that is a few years onls and I plan to to use that as the PC.

I did not know about the chips so I will have to check on them before I get to much into this.

The reason I requested the schematic in SCH form is just to save time not having to re-create the components from scratch.

Thanks again,

Mike


Reply
Share: