Ren64 help please !...
 
Notifications
Clear all

Ren64 help please !!

10 Posts
8 Users
0 Reactions
3,629 Views
Posts: 112
 fj
Topic starter
(@fj)
Estimable Member
Joined: 19 years ago
[#11370]

hi there,

i've been soldering up a Ren64 and i've made a mistake. i've soldered in the optional bussed resistors around the wrong way !!! aaarrrgghhhh...i've been kicking my own butt over that stupid mistake.

is the only way to fix it to pull the resistors out and put them in the correct way? i've tried on one of them by using solder wick but it doesn't get enough of the solder out to be able to remove the resistor buss, so is there a better way?

next question - the instructions call for diodes d1, d4 and d5 to be orientated with the band in the square hole. what about diodes d2, d3, d6 and d7? are they to be the same way or opposite?

thanks, fj


9 Replies
g2ktcf
Posts: 3651
(@g2ktcf)
Famed Member
Joined: 18 years ago
fj wrote:hi there,

i've been soldering up a Ren64 and i've made a mistake. i've soldered in the optional bussed resistors around the wrong way !!! aaarrrgghhhh...i've been kicking my own butt over that stupid mistake.

is the only way to fix it to pull the resistors out and put them in the correct way? i've tried on one of them by using solder wick but it doesn't get enough of the solder out to be able to remove the resistor buss, so is there a better way?

next question - the instructions call for diodes d1, d4 and d5 to be orientated with the band in the square hole. what about diodes d2, d3, d6 and d7? are they to be the same way or opposite?

thanks, fj

All diodes should be installed with the band matching the silkscreen on the board. Now for removing the bussed resistors, I would use a solder sucker followed by solder wick. But, did you put any flux on your wick?? It does not work very well without it.


Reply
Posts: 112
 fj
Topic starter
(@fj)
Estimable Member
Joined: 19 years ago

the silk screen shows d1-d4 orientated the same way so i'll put them all in the same way as the instructions say for d1 and d4.

thanks for the help.


Reply
Posts: 1424
(@oldcqr)
Noble Member
Joined: 18 years ago

Desoldering Iron. Can't live without it:
http://doityourselfchristmas.com/forums/showthread.php?t=9920


Reply
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

RE: removal of the bussed resistors.

Do you have extras? If you do, just clip off the whole resistor and you will find it's pretty easy to heat and remove the remaining tiny piece of wire in each hole.


Reply
rjchu
Posts: 1191
(@rjchu)
Noble Member
Joined: 17 years ago

...just be careful. If you apply too much heat for too long to any of the solder pads they might start to separate from the PCB material which isn't good either.

-joni-

ukewarrior wrote:RE: removal of the bussed resistors.

Do you have extras? If you do, just clip off the whole resistor and you will find it's pretty easy to heat and remove the remaining tiny piece of wire in each hole.


Reply
Posts: 1041
(@christmas-light)
Noble Member
Joined: 18 years ago

what about using some of this ?:)


Reply
Penfold
Posts: 1235
(@penfold)
Noble Member
Joined: 19 years ago

FJ what solder blend are you using. If you are using Lead free I would say you are better off buying new resistor packs and sacrificing the ones you have in there now (It was mistakes like this that I went over to 37/63).

Soaking your wick in liquid flux does help immensely! What you might try doing also, is that if you are unable to get the solder out you might try to add more solder to the connection and try to wick it up again. I would definitely go the route of using a solder sucker first then using the wick.

Other people swear by the desoldering tool that OLDCQR recommended.


Reply
Posts: 175
(@aususer)
Estimable Member
Joined: 17 years ago

I concur with penfold: it might sound counter-productive, but ADD solder to the pads - then desolder them.
The added solder will also assist in the joint holding its heat a little longer (especially with these thru-holes)
Also make sure you give plenty of cooling time between pins or - as others have said - you'll damage the board/pins.

tip2: You might also find wiggling the array gently after you desolder each pin might make the joint "dry" and ease removal..

tip3: hold the board in a vice (so you can work from both sides - protect the board with cardboard), run the iron down the pins on one side and gently pull on the array from the other (if your good at it, the burns you will get will heal in only a couple of weeks ;)).

If your coming to the mini - bring it and yr wick along and I am sure one of us can give you a hand.
BTW: well done for giving the ren a go!! 😉 I might send my next board to you "for practice" 😀


Reply
Posts: 112
 fj
Topic starter
(@fj)
Estimable Member
Joined: 19 years ago

thanks for the tips everyone.


Reply
Share: