Ren 64 hook up prob...
 
Notifications
Clear all

Ren 64 hook up problem

21 Posts
4 Users
0 Reactions
7,073 Views
Posts: 448
Topic starter
(@bobkeyes)
Honorable Member
Joined: 17 years ago
[#11375]

I have a ren64 which I used with great success last year. It was mounted on a wall in my basement. I decided to remove it and mount it in an enclosure for use on my mega tree this year. Now the problem.

In the move I pulled the RJ45 input connector loose. No problem, I said, I'll just replace it with a new one. I did and now the ren64 won't blinky flashy. I think I pulled loose some of the traces as a couple did not want to solder back properly.

Does anyone know where these RJ45 pins connect on the ren64 board? If I knew that I would just hard wire them to be sure of this connection.

Any help would be greatly appreciated!!!:D


20 Replies
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

The schematic is in the Wiki - you can start there and trace things out on your board. See http://www.doityourselfchristmas.com/wiki/images/6/66/Renard64_xc.pdf

The Wiki also has a PCB layout so you can compare to that as well.


Reply
Posts: 448
Topic starter
(@bobkeyes)
Honorable Member
Joined: 17 years ago

I thought I could wire this up straight, but checking with an ohm meter it all checks good.

I AM REALLY IN A PANIC HERE!! My daughters wedding is Sat. and I need this to do the lights. It's an outside evening wedding. Now I can't get the board to run.

I ran diag. software and it seems to run ok so the board itself is good.

I know there is a signal because the same lead from computer runs a 24lv and mighty mini fine. It just will not light up the ren64.

Could someone help please??


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

Can you post some close-up pictures - both sides around the RJ45 connector that was pulled. The key thing is pins 4 and 5.


Reply
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

Bob,
Here's a jpg of the circuitboard traces in the wiki. You should be able to see where they go here. My guess is that there's a short on pins 4 or 5 as those are pretty small and look to me to be the most likely that would get damaged.

Pin 4 goes to the LEFT side of R3. Pin 5 goes to the LEFT side of R4.
Pins 1-2 are of course ground.

http://www.doityourselfchristmas.com/wiki/index.php?title=Renard64

If worst comes to worst, let me know and I can overnight a Ren64 to you -- you'd have it Friday.


Reply
Posts: 448
Topic starter
(@bobkeyes)
Honorable Member
Joined: 17 years ago

Thanks guys. Here is what I have. Measuring from pin 1, to 2 dead short, as it should be I think. pin 3 open. Pin 4 open. Pin 5 connection with 11.23 k ohm. Pin 6 dead short. Pin 7 open. Pin 8 open.

Pin 5 is shorted to 1,2,and 6 with 6 showing 11.28k ohm. I think 5 is my problem. What say you?


Reply
Posts: 448
Topic starter
(@bobkeyes)
Honorable Member
Joined: 17 years ago

Thanks Dirk. You're a Gem for offering, but I hope I don't have to resort to that.

dirknerkle wrote:Bob,
Here's a jpg of the circuitboard traces in the wiki. You should be able to see where they go here. My guess is that there's a short on pins 4 or 5 as those are pretty small and look to me to be the most likely that would get damaged.

Pin 4 goes to the LEFT side of R3. Pin 5 goes to the LEFT side of R4.
Pins 1-2 are of course ground.

http://www.doityourselfchristmas.com/wiki/index.php?title=Renard64

If worst comes to worst, let me know and I can overnight a Ren64 to you -- you'd have it Friday.


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

Should have asked earlier - - are you running RS-232 or RS-485? If RS-232, then pin 5 should actually be grounded through JP1 and should show as a dead short to ground. Again, if RS-232, then pin 4 is the real key - it goes through a 1k resistor to pin 7 on the 75176 chip.

Honestly, I would take the Dirkmeister up on his offer as a Plan B - it's only a bit of postage back/forth.


Reply
Posts: 448
Topic starter
(@bobkeyes)
Honorable Member
Joined: 17 years ago

Running 485.


Reply
Posts: 448
Topic starter
(@bobkeyes)
Honorable Member
Joined: 17 years ago
dirknerkle wrote:Bob,

If worst comes to worst, let me know and I can overnight a Ren64 to you -- you'd have it Friday.

OK Dirk. Are you sure you don't mind?? It would be a lifesaver for me. I think it's going to take some major rework on this board.

Express mail DOES NOT do well here. It's always 2 days. UPS or FEDEX maybe??

I'll PayPal the postage plus some for gas and trouble.

Gosh, I feel better already.

Please let me know if you've had second thoughts. Of course I'll be responsible for the board.


Reply
Page 1 / 3
Share: