Ren-w problem
 
Notifications
Clear all

Ren-w problem

28 Posts
8 Users
0 Reactions
7,870 Views
LabRat
Posts: 2981
(@labrat)
Famed Member
Joined: 17 years ago

I would agree that you have demonstrated that the PC (#2) is transmitting the data.
So at this point we have to focus on the receivers. Sooooo... starting with the blatantly obvious, and I apologize
if it sound condescending, but these are all snafu's that have caught me within the last 2 days.
a. Power - have you got the +5v and GND going into the Rx pcb? (Little green light is lit?)
b. What version of the REN-W's? Is this the version that supported two modules at once? Is the XBEE on the Rx side?
(don't roll your eyes... I lost 20 minutes to this the other night)
c. Cable - based on what you have written, it certainly sounds like a possible cabling issue.
d. Addressing - can you move the module that has proven to "receive" on PC#1, to the talk to the REN64?


Reply
LabRat
Posts: 2981
(@labrat)
Famed Member
Joined: 17 years ago
rjchu wrote:One more thing to look at, do your plug-in/COM port settings in Vixen match the configuration of the XBee's? For RenW's this is typically 57600 baud, 8, *M*, 1.

Thanks,

-joni-

Good point, but as we are seeing the data being Rx on the second PC, that would imply that the Tx side is correct.
(Hmm.. I suppose it could be transmitting garbage)


Reply
dirknerkle
Posts: 10310
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
LabRat wrote:(Hmm.. I suppose it could be transmitting garbage)

Simple test for the data format:

Use a USB Explorer with an xbee in it, connect to it with XCTU software, open the XCTU terminal screen in "show hex" mode. Then from another computer (or the same one connected to Ren-W in transmit mode) you can use the channel test function in Vixen, selecting ALL channels ON. The XCTU terminal screen in receive mode will display 7E 80 FF FF FF FF FF FF (and etc) for as many channels as you have the plugin set to if it is working properly. It's very orderly and consistent. If there's anything else, either a setting is wrong or the data being transmitted is not serial data in the proper format and Ren-W is simply not going to work.


Reply
Posts: 448
Topic starter
(@bobkeyes)
Honorable Member
Joined: 17 years ago
LabRat wrote:I would agree that you have demonstrated that the PC (#2) is transmitting the data.
So at this point we have to focus on the receivers. Sooooo... starting with the blatantly obvious, and I apologize
if it sound condescending, but these are all snafu's that have caught me within the last 2 days.

Don't worry about sounding "anyway". I just want to get it talking!!

a. Power - have you got the +5v and GND going into the Rx pcb? (Little green light is lit?)
Yes, Power is there.
b. What version of the REN-W's? Is this the version that supported two modules at once? Is the XBEE on the Rx side?
(don't roll your eyes... I lost 20 minutes to this the other night)
This is v6. It is the single XBee board.
c. Cable - based on what you have written, it certainly sounds like a possible cabling issue.
Cables have been checked and rechecked. Then they were changed out and changed again.
d. Addressing - can you move the module that has proven to "receive" on PC#1, to the talk to the REN64?

The module that is proven is only the XBee part. It is mounted on the programming board. But, yes. All XBees have been proven to receive in the programming board.

As to the comport settings. I don't use a comport. The E1.31 plugin gets it's signal via ethernet. It then converts it to 485 to make the Renards work.


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago
bobkeyes wrote:The module that is proven is only the XBee part. It is mounted on the programming board. But, yes. All XBees have been proven to receive in the programming board.

As to the comport settings. I don't use a comport. The E1.31 plugin gets it's signal via ethernet. It then converts it to 485 to make the Renards work.

But there are settings on the E1.31 bridge - at least for baud rate - I assume this is RPM's bridge you have?


Reply
Page 2 / 6
Share: