Conversion to Wirel...
 
Notifications
Clear all

Conversion to Wireless

57 Posts
24 Users
0 Reactions
21.5 K Views
corytcline
Posts: 1249
(@corytcline)
Noble Member
Joined: 16 years ago
griffixdc wrote:Alright, alright some of the questions i had an idea but i was not for certain... so i was asking to see if any body else had success or difficulty say using a stainless steel enclosure...would there be a way to extend the antenna longer than 8 inches or at least long enough to reach outside of the enclosure? the stainless steel enclosure is 12X12 x 6 inch deep and hard to drill wholes in it ...so i was thinking if there was a way to extent the antenna out the logic hole i pre set it could maybe see light to the radio waves ( but the antenna would have to be minimally 8 inches long to even hit the edge where the hole is placed being on the bottom for water proof concept.

i am not sure i under stand how to do this 2 stop bits or if i understand what your saying precisely i am gathering i need to delay something 2 bits but what am i delaying?

I have one in a converted metal breaker box. I stripped all the breakers out and mounted the renard and Renw inside. My Renw just has an xbee pro 1". I transmit from a xbee explorer board inside my house that also has an xbee pro 1" antenna. Never had an issue yet. Right now my controller in the metal box is about 50' from the house on the other side of my halloween tunnel. So its going thru one layer of wood siding, one layer of vinal siding , two layers of plywood on the tunnel and the metal box the controller is mounted in no issues all working great!!


Reply
Festus
Posts: 508
(@festus)
Honorable Member
Joined: 15 years ago
dirknerkle wrote:I've got the DIGWDF engineers working on it....

Have those lutefisk eating maniacs figured it out?


Reply
Posts: 92
(@macshroom)
Estimable Member
Joined: 13 years ago

hi,
ive read all of this and from what I understand . the wireless you are discussing is a signal from the controller(like a ren ss24) to the lights.
is there a way to make it wireless from my PC to the ren SS24?
can I have my PC in my basement and the RENARD SS24 mounted in my garage .have the signal sent wirelessly to the renard,but still hardwire all the lights to the renard?
would save me about 100ft of that big 9 pin port cable .
thanks .


Reply
kychristmas
Posts: 3955
Topic starter
(@kychristmas)
Famed Member
Joined: 18 years ago

Actually, it's the opposite. The wireless being discussed here IS the computer to controller. Look for dirknerkle's stuff. There's also some newer stuff from Komby. Both will be in the $75-90 range to get a transmitter and receiver setup.

You do know you can convert the serial signal to I expensive cat 5 cable right out of the computer, right? It's much cheaper and easier to run through walls and such.


Reply
Posts: 92
(@macshroom)
Estimable Member
Joined: 13 years ago

holy moses I didn't know that. thanks dude!just found a sweet deal on that cat5 cable. http://www.aliexpress.com/item/Free-Shipping-30M-100ft-CAT5E-CAT5-RJ45-Ethernet-Internet-Network-Patch-Lan-Cable-Cord-Blue/836900463.html
one more checked off the list . thanks again KYChristmas.


Reply
Posts: 92
(@macshroom)
Estimable Member
Joined: 13 years ago

and ive found 100Ft for half that price on ebay . cool!


Reply
smeighan
Posts: 2595
(@smeighan)
Famed Member
Joined: 15 years ago
MacSHROOM wrote:holy moses I didn't know that. thanks dude!just found a sweet deal on that cat5 cable. http://www.aliexpress.com/item/Free-Shipping-30M-100ft-CAT5E-CAT5-RJ45-Ethernet-Internet-Network-Patch-Lan-Cable-Cord-Blue/836900463.html
one more checked off the list . thanks again KYChristmas.

I think many people buy their stranded cat 5 cable from mono price.com

I have gotten a few thousand feet from them.

Sean

Sent from my iPad using Tapatalk HD


Reply
Posts: 499
(@frederic)
Honorable Member
Joined: 14 years ago
MacSHROOM wrote:hi,
ive read all of this and from what I understand . the wireless you are discussing is a signal from the controller(like a ren ss24) to the lights.
is there a way to make it wireless from my PC to the ren SS24?
can I have my PC in my basement and the RENARD SS24 mounted in my garage .have the signal sent wirelessly to the renard,but still hardwire all the lights to the renard?
would save me about 100ft of that big 9 pin port cable .
thanks .

One way to put "serial" on the lawn driving a bunch of Renards or other serial-based lighting controllers is to use a "terminal server". A terminal server usually has four or more RS232 serial ports that can be connected to Renards, and an ethernet jack to connect to your home network. While you can hardwire that ethernet jack to your network, you can also plug in a wifi access point (netgear, Linksys, Dlink) and bridge your network that way. To drive the terminal server serial ports you have to load a driver from the terminal server manufacturer, and viola, your Vixen PC has new serial ports that are wirelessly out on the lawn.

I experimented with a setup like this over the summer and really liked how it turned out. However, since I'm running power for my Renards anyway, tossing in a cat5 for serial (rs485) really isn't a big deal so I'm going that route.

But the wifi/terminal server combination does work. Of course the devices aren't intended to be on the lawn so you'll have to protect them from the weather.


Reply
kychristmas
Posts: 3955
Topic starter
(@kychristmas)
Famed Member
Joined: 18 years ago
frederic wrote:One way to put "serial" on the lawn driving a bunch of Renards or other serial-based lighting controllers is to use a "terminal server". A terminal server usually has four or more RS232 serial ports that can be connected to Renards, and an ethernet jack to connect to your home network. While you can hardwire that ethernet jack to your network, you can also plug in a wifi access point (netgear, Linksys, Dlink) and bridge your network that way. To drive the terminal server serial ports you have to load a driver from the terminal server manufacturer, and viola, your Vixen PC has new serial ports that are wirelessly out on the lawn.

I experimented with a setup like this over the summer and really liked how it turned out. However, since I'm running power for my Renards anyway, tossing in a cat5 for serial (rs485) really isn't a big deal so I'm going that route.

But the wifi/terminal server combination does work. Of course the devices aren't intended to be on the lawn so you'll have to protect them from the weather.

I think its great to play around, but your solution is far more expensive and more complicated than Dirk's Xbee or a Komby setup.


Reply
CaptKirk
Posts: 2200
(@captkirk)
Noble Member
Joined: 16 years ago
kychristmas wrote:Actually, it's the opposite. The wireless being discussed here IS the computer to controller. Look for dirknerkle's stuff. There's also some newer stuff from Komby. Both will be in the $75-90 range to get a transmitter and receiver setup.

You do know you can convert the serial signal to I expensive cat 5 cable right out of the computer, right? It's much cheaper and easier to run through walls and such.

It is that expensive when dealing with the Xbee modules, but not for the Komby stuff.

The receiver would be an RF1 + NRF at $12 (including the parts) The transmitter RF1 option would be $20 because you want the high power NRF module substituted for the "zig zag" NRF. Remember the NRF is only $1 for the lower power transceiver, and $9 for the high power one better for the transmitter. And these communicate at 250k baud so they are fast enough for DMX.


Reply
Page 5 / 6
Share: