Controller Locking ...
 
Notifications
Clear all

Controller Locking Up

14 Posts
7 Users
0 Reactions
3,818 Views
rstehle
Posts: 4348
Topic starter
(@rstehle)
Illustrious Member
Joined: 19 years ago
[#5378]

I don't know if this is a Controller problem, or a Vixen problem. I am running 384 channels on 3 com ports. Com 1 is a mixture of Ren 16's and Ren 24's. Com 3 is all Ren 16's, and they all work properly. My problem is on my last com port (Com 4). I have the least amount of channels on this port (80), the first controller is a Ren 24, then a Ren 16. They both work well. My problem is with the next 2, a Ren 16 and another Ren 24. I find that during particularly busy parts of the sequence on that port, Ren 16 #2 will lock up on channel 2, and the Ren 24 after it will not respond. I have to shut off power to them to get them to reset, but then they will act the same way again. I am using RS232 to RS485 converters, and have them grounded to the Power Supply. The one thing I am suspicious of is that the cat 5 going from Ren 16#2 to the last Ren 24 goes over my driveway via a driveway arch (25') that has LED's on it. The lockups occur toward the end of the sequence when the arches are in rapid motion. Might I be getting garbage induced onto the Cat 5 from the LED's on the arch? The other thing I have noticed is that this problem seems to get worse the colder it gets outside.......... Help!


13 Replies
Wayne J
Posts: 7789
(@wayne-j)
Illustrious Member
Joined: 20 years ago

On the Ren 16 #2 remove and replace the RS485 ICs. As well as the PIC for the first 8 channels. Something I have seen is, the sockets tend to loose connection (for whatever reason) and things go a bit haywire. Just simply remove the compontents and push them back in. See if that helps.


Reply
RavingLunatic
Posts: 1502
(@ravinglunatic)
Noble Member
Joined: 19 years ago
rstehle wrote:.....The other thing I have noticed is that this problem seems to get worse the colder it gets outside.......... Help!

Are you using the 595-SN75176BP chip? If so, it is only rated down to 0°C or 32°F for us non-metric folks. Try the 595-SN65176BP or some of the other options in the latest Ren-16 BOM. It might help you on those cold nights in Idaho. 😀


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

In addition to the suggestions from Wayne and RL, another thing to double check is the power to that Ren16. The electrolytic caps used on the power supplies don't always work well at low temperatures, they lose some of their capacitance at below-freezing temps, and some of the other components may have issues as well.


Reply
rstehle
Posts: 4348
Topic starter
(@rstehle)
Illustrious Member
Joined: 19 years ago

Thanks for the suggestions gang.

Wayne, I reseated the IC's on Ren 16 #2 and that seems to have taken care of that problem. But, it is kind of hard to find all the gliltches in the bright daylight.

RL, I am using RS485 chips that are rated down to well below zero

Phil, I have 11.9 volts at the problem Ren 16.

Like I said, that one seems to be taken care of for now........ however, I have a new gremlin. I have a Renard 24 that is the first controller in the line on that com port (4). At some point near the end of the sequence, one of the first few channels on that controller will hang in the on position. Stays that way even after the sequence is finished. Goes off if I reset power to the controller. I checked the Cat 5 cables, changed RS232 to RS485 adapters, changed PIC's, changed RS485 chips, no change.............. any ideas?

Starting to get frustrated................


Reply
Wayne J
Posts: 7789
(@wayne-j)
Illustrious Member
Joined: 20 years ago

Those channels staying on, may be in the sequence. Look at the sequence at the very end and see if the cells at the very end of the sequence have activity. If so, just select the entire column and click OFF and save, see if that fixes it. Then make sure you have 'reset controller at end of sequence' checked in the preferences/sequence execution.


Reply
rstehle
Posts: 4348
Topic starter
(@rstehle)
Illustrious Member
Joined: 19 years ago

Unfortunately, that didn't fix it. The controller appears to be hanging a channel on at some point during a sequence, usually about mid way, and from then on, that controller does not respond, nor do any after it in line..............


Reply
Wayne J
Posts: 7789
(@wayne-j)
Illustrious Member
Joined: 20 years ago

Find out which PIC controls that channel and try to reseat it. If that don't work, give it a re-flash.


Reply
rstehle
Posts: 4348
Topic starter
(@rstehle)
Illustrious Member
Joined: 19 years ago

I tried swapping controllers to see if I just had a lemon (yes, I built them all). I was so happy, it played the same sequence it hung on previously from start to finish perfectly!! I was ready to plug in my tune to sign and start my show. But, I thought I would test a couple more songs before that, so I played Wizards. Back to the same old thing, played about half way thru and then that section hung and no more blinky flashy................. I am going to put it away for tonight, (and maybe tomorrow too.............)


Reply
Posts: 464
(@holtm)
Honorable Member
Joined: 19 years ago

When you swapped controllers, was it the same controller that locked up or the same SSR? If it is the SSR, you may want to read the end of this thread.
http://doityourselfchristmas.com/forums/showthread.php?t=5246


Reply
Page 1 / 2
Share: