RGB pixel turned Se...
 
Notifications
Clear all

RGB pixel turned Servo controller

7 Posts
5 Users
0 Reactions
5,305 Views
Posts: 1084
 ben
Topic starter
(@ben)
Noble Member
Joined: 19 years ago
[#3965]

Ok, I need a DMX servo controller to control 5 channels. So I am taking JEC's RGB pixel +servo and making it my own. I used his schematic to start designing but I have a question. Can I just use the MAX RS485 chip to run the first and 2nd PIC 16F688's?? Or do I need to use 2 of them? I also planned to use one 7805 regulator. How does this sound? Here is his schematic,
http://www.response-box.com/rgblights/Media/Photos/sixservosch.pdf

I am making this as a single sided home etch board. I just need to make 3 or 4 of these quick. If it works and there is an interest I can double side it get a BOM together and place an order for them. Please advise if what I said above will work.

Ben


6 Replies
Posts: 1084
 ben
Topic starter
(@ben)
Noble Member
Joined: 19 years ago

Ok, here is what I came up with. This is 4 of them. I know I probably left something out. I used .015" traces on everything except the 12V which I used .025" traces. I didn't go smaller because it makes it easier for me to home etch.

Ben


Reply
Posts: 386
 JEC
(@jec)
Reputable Member
Joined: 19 years ago
ben wrote:Ok, here is what I came up with. This is 4 of them. I know I probably left something out. I used .015" traces on everything except the 12V which I used .025" traces. I didn't go smaller because it makes it easier for me to home etch.

Ben

There's no reason why a single '688 couldn't drive 10+ servo motors simultaneously...

Edit: Make that 10 total. It's a 14 pin chip, less power, ground, TX and RX on the UART.


Reply
Posts: 1084
 ben
Topic starter
(@ben)
Noble Member
Joined: 19 years ago
JEC wrote:There's no reason why a single '688 couldn't drive 10+ servo motors simultaneously...

Will you write the codefor me ? 😉 That is what I was using what was already there because I cannot code. If you can cut and paste or whatever to give me 5 servo outputs then thank you 🙂 Thats all I need.

Ben


Reply
Posts: 1041
(@n1ist)
Noble Member
Joined: 19 years ago

Two things that you may want to look at:

- Most servo connectors have pins on .1 centers. You can change the holes to .040 size to make that work (a .025 square post is .035 on the diagonal, but you need to make the hole a touch bigger to allow for tolerance stackup. I had real fun with a 64-pin connector once 🙂

- Treat ground like power. It should be at least as wide.

BTW, your board is not single-sided. It should be easy to get almost all of that on the circuit side.

/mike


Reply
Posts: 1084
 ben
Topic starter
(@ben)
Noble Member
Joined: 19 years ago
n1ist wrote:Two things that you may want to look at:

- Most servo connectors have pins on .1 centers. You can change the holes to .040 size to make that work (a .025 square post is .035 on the diagonal, but you need to make the hole a touch bigger to allow for tolerance stackup. I had real fun with a 64-pin connector once 🙂

- Treat ground like power. It should be at least as wide.

BTW, your board is not single-sided. It should be easy to get almost all of that on the circuit side.

/mike

I scrapped this idea for Now. I talked with JEC and there might be a servo controller later but for now I am set.

Ben


Reply
Posts: 2
(@lightingdoc1)
New Member
Joined: 18 years ago

Hello Ben,

Here is a link to a dmx to servo controller

http://home.att.net/~northlightsystems/DMX512toRCservo.htm

I have 72 of johns rgb pixels on my house and they work great, however it appears you require some special coding maybe this will help.

Rick


Reply
Share: