So I've been working on this project for about 6 months. It was an idea I had about a year ago but didn't have the time. When the Helix was created it had the major piece of code I needed to get going, the dimming engine/driver (thanks Greg).
Feature List:
Parallax Propeller (SMD due to shortage of DIPs)
USB via FTDI FT232RL (on board programming, virtual serial interface - SMD)
Phase Angle Dimmer Control - 32 channels, expandable to 64 (no SCRs)
DMX/RS485 (wired to allow bidirectional simplex communication for RDM)
Ethernet (Wiznet - ArtNet)
Character LCD - 8x2
Push buttons - qty 4
Temperature sensor(s) both on-board and remote (via OneWire - DS18S20)
The dimmer is a powered by the Parallax Propeller and uses the Helix dimmer control engine. This dimmer has an Ethernet and I'm currently working on the code to support ArtNet. There is a UI to change settings like start address, dimmer patch, and dimmer mode, via the LCD and four push buttons.
This is a "fully featured" controller/dimmer, my goal wasn't to create the least expensive dimmer it was to create the most fully featured. Further I wanted something that allowed Ethernet based control. Finally I wanted something that anyone could customized and learn with. The Propeller's development environment is free and well documented which means anyone can learn how to use it and customize it to their needs.
How can it be used?
Basic DMX Dimmer (which is how I plan to use it initially)
USB dimmer and DMX dongle (the DMX interface could be set to output DMX)
Ethernet Dimmer and DMX node (DMX out)
Renard Dimmer and RS485 dongle (future)
Can support RDM, ArtNet, or ACN. (I've got ArtNet basically working, need to optimize the code)
Current Status
I am able to control the dimmers via DMX, I have a multiple selectable dimmer curves working also (Linear, Scurve, switched, preheat). I'm also able to control it via USB with the OpenDMX driver. Finally, I've built one complete prototype, but had 4 additional PCBs made (PCB cost was ~$19).
When can we expect it?
The hardware is complete but the firmware needs a bit more attention. I'm a hobbyist so I do this in my spare time. I intend to provide updates as I go in this thread.
UPDATE:
08/21/2009 Revision B of schematics posted.
09/03/2009 Revision C of schematics posted
11/05/2009 PCBs arrived and one is fully populated.
01/10/2010 Revision D of schematics posted
Hey ben,
This looks really interesting. Have you got a schematic floating around? Bit hard to see how it hangs together from teh photo. I'd be really interested in having a look at your art-net code as well. I've started some work on trying to implement art-net on a PIC, but as yet, not made much progress.
I'd love to implement a ethernet controller for the tripix.. ( my head end controller speaks art-net ), currently i externally convert 8 universes from art-net to dmx.. Getting rid of the dmx completly would be grand.
I'm still cleaning up the schematics but should have them ready for review very soon. I'm will either post them here or in development. As far as the Artnet code its written in Spin and the Ethernet driver (for the WizNet module) is written in PASM. While it works, sort of, it can only handle one universe being transmitted at a time.
Schematics are posted for review, let me know what needs to change.
right. I'm going to buy me a prop development system
looks good but im a little concerned about having such a large cap on the output of the 5V regulator. Seems to me it should be on the input not the output of the reg
DynamoBen wrote:I'm still cleaning up the schematics but should have them ready for review very soon. I'm will either post them here or in development. As far as the Artnet code its written in Spin and the Ethernet driver (for the WizNet module) is written in PASM. While it works, sort of, it can only handle one universe being transmitted at a time.
Ben, do you have any perspective on why it will only handle one universe? ( i need eight! ).. Does it run out of compute power?
Would you be able to post your code?
Wombat wrote:looks good but im a little concerned about having such a large cap on the output of the 5V regulator. Seems to me it should be on the input not the output of the reg
Frankly thats a copy paste from another design, not sure what happened there. What about a set to 10uf caps, better?
mrpackethead wrote:Ben, do you have any perspective on why it will only handle one universe? ( i need eight! ).. Does it run out of compute power?Would you be able to post your code?
I've done 7 DMX outs (1 cog is reserved for SPIN, there is not changing this). All you do is launch the DMX object into 7 open cogs. However for this project if all the options are used I'm pretty close to using every cog.
I will post some code once I have the schematics nailed down. While I have most of the basics running there are still some things I need to sort out/get working. BTW most of the drivers I'm using are other from the object exchange (obex) or are slightly modified for my purposes. The only really custom cost is the parent object that stitches everything together. Go here to see whats available already: http://obex.parallax.com/ (I'm using the DMX objects in my project, bonus points if you find my username in the notes of one of them)
DynamoBen wrote:Frankly thats a copy paste from another design, not sure what happened there. What about a set to 10uf caps, better?
10uf would be much better. having such a large cap would not only take up huge real estate on the board it would probably cause the regulator to be less stable than it should be.
