DMX System
 
Notifications
Clear all

DMX System

13 Posts
6 Users
0 Reactions
6,027 Views
Posts: 118
Topic starter
(@larry-hazeltine)
Estimable Member
Joined: 17 years ago
[#7796]

There is a lot of information on here about DMX but I can't seem to find exactly what I'm looking for. Maybe what I'm trying to accomplish has been done before, but I haven't found it yet.

My current system is a PC running LOR. I have the LOR serial/485 adapter connected to the computer and cat5 daisy chained from controller to controller.

For various reasons I'm expanding my channel count with two 24 channel Renard controllers instead of buying more LOR controllers. I've been told I can connect Renard and LOR together if I'm running DMX and the Vixen software.

1. What is the simplest way to get my computer to output DMX for the controllers? I'm assuming they will stay daisy-chained with cat5, but I'll need an adapter or dongle to connect that cat5 to the computer instead of the serial/485 adapter I have now.

2. I'm under the impression that I can setup part of a Renard board to output 24VDC for use with something like the RGB+W LED floodlights. Is the DC output PWM* to allow for dimming or do I need another board for that. I know, that isn't a DMX question, but if the answer is "no" then is there another DMX-capable device that can do what I want.

* If I understand the concept correctly, you can't just lower the DC voltage on an LED to dim the light output because once the low voltage threshold is reached the LED will just turn off. To give the appearance of dimming, either the PWM pulse or duty cycle is changed so the LED is on for less time each cycle but the pulses are fast enough that we can't see the off part of the cycle, therefore giving the illusion that the light isn't as bright.


12 Replies
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

I have an Enttec USB Open DMX interface which I wired to my LOR controllers with the appropriate XLR->RJ45 mapping (on the Wiki) and run the LOR via Vixen. The LOR boxes use the unit IDs to define the DMX starting address (the LOR website has the details). I do not have DMX based Renards but you should be able to daisy-chain to/from the LOR boxes. One caveat is that the LOR RJ45 pinout is different than Renard RJ45 pinout for the RS-485 interface so you have to swap signals.

My suggestion would be to put the LOR boxes up high in the DMX address list to ensure they don't get confused with the Renards when you set them up.

And yes - dimming is really just controlled on/off and not voltage adjustments to the LEDs.

I'll be moving up to Robert's DMX dongle (jump on the bandwagon!) coop as I've heard of various issues with the Open dongle. I'm using my LOR RS485 dongle to run my LEDTriks panel!


Reply
mrpackethead
Posts: 2289
(@mrpackethead)
Famed Member
Joined: 19 years ago
Larry Hazeltine wrote:
* If I understand the concept correctly, you can't just lower the DC voltage on an LED to dim the light output because once the low voltage threshold is reached the LED will just turn off. To give the appearance of dimming, either the PWM pulse or duty cycle is changed so the LED is on for less time each cycle but the pulses are fast enough that we can't see the off part of the cycle, therefore giving the illusion that the light isn't as bright.

Something to understand here. The light output of a led, is dependent on the current flowing through it, irrispective of the voltage thats being dropped across it. You need a voltage thats at least as high as the Vfd ( forward voltage drop ) for the led.. This varys between led types, but can be anthing between about 1.5 and 4V.

The easiest way to control how much current flows through a LED is to use a current limiting resistor. If you turn your circuit on, the led will glow at a particular intensity that is related to the resistor.. If you lower the value of the resistor the led will low more brightly, if you increase the value, it will glow less brightly.. So if you were happy to run around changing resistors very rapidly during your show, you could simply ahceive dimming by chaning resistors! Thats far from practical however is it..

So, you set the resistor so that the led is running at say 90-100% of its maximum rated current, when you turn the circuit on. By modulating the circuit with PWM, you can modify the average current following through the circuit.. ( if you modulated a circuit that drew 50mA, at 50% PWM, the average currently would be 25mA ). If you did this at say 1Hz, you'd see a 'half' lit led, flashing on and off.. If you increase the frequency from 1hz to say 20Hz, you'll start to see a continously lit led, as opposed to a 'flashing' led but it will appear to flicker.. Keep increasing it to 50Hz, you'll start seeing the flickering dissapearing, but you can get 'beats' occuring with other stuff around the place.. Keep increasing past 80hz, and the brain can no longer distinigush the on/off and effectively your brain just sees it as a continous 'on', but it can tell that its dimmed. Theres been lots of research into what the 'refresh rate should' be.. Some people reportably can still detect flicker at 90Hz.. I have tryed this experiment myself and i could see flicker till about 75Hz. The really flash tv's refresh at 100Hz.

My Led pixels modulate at 150hz, cause it was an easy frequency to set up in teh uProcessor, and they appear nice and smooth..


Reply
dmcole
Posts: 2196
(@dmcole)
Noble Member
Joined: 19 years ago
budude wrote:I'll be moving up to Robert's DMX dongle (jump on the bandwagon!) coop as I've heard of various issues with the Open dongle. I'm using my LOR RS485 dongle to run my LEDTriks panel!

Here's the link:

http://doityourselfchristmas.com/forums/showthread.php?t=7918

\dmc


Reply
Posts: 118
Topic starter
(@larry-hazeltine)
Estimable Member
Joined: 17 years ago

Thanks. I'm planning on buying the DMX dongle from the co-op this week.

My setup now look like this:
PC > USB/DMX Dongle > cat5 > Renard(s) > cat5 special* > LOR(s)

* one end terminated with Renard pinout, the other with LOR in.


Reply
Posts: 118
Topic starter
(@larry-hazeltine)
Estimable Member
Joined: 17 years ago

Thought of one more thing...I'm not sure I can put the Renards first in line without running a whole lot more cat5. Can you run DMX through a Y-adapter or splitter so that you have branches in the line or does it have to run from device to device? Basically, the In and Out would have the same pin arrangements (for LOR to LOR) and the spur would have the pinout for Renard.


Reply
dmcole
Posts: 2196
(@dmcole)
Noble Member
Joined: 19 years ago
Larry Hazeltine wrote:Can you run DMX through a Y-adapter or splitter so that you have branches in the line or does it have to run from device to device?

Larry:

Adapter? No. Splitter? Yes. DMX is based on RS-485, which has a daisy-chain topology and you can't just branch off in the middle of the chain.

Robert has a DMX splitter spec'd out here

http://doityourselfchristmas.com/forums/showthread.php?t=7508&highlight=dmx+splitter

but he so far hasn't brought this to a co-op status.

RJ is running a splitter PCB co-op right now over at his site

http://diylightanimation.com/index.php?topic=1684.0

If you're adventurous, there are plenty of DMX splitter schematics floating around the web and you could build your own.

\dmc


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

Is there a reason you can't put the Renard at the end of the RS-485 line? I don't know your controller physical layout so it's hard to tell... Probably cheaper to just have two runs of Cat5 although there are other advantages to using a splitter such as supporting more devices down the road.


Reply
Posts: 118
Topic starter
(@larry-hazeltine)
Estimable Member
Joined: 17 years ago
dmcole wrote:Larry:

Adapter? No. Splitter? Yes. DMX is based on RS-485, which has a daisy-chain topology and you can't just branch off in the middle of the chain.

Is the signal modified between the IN and THRU (or OUT) on a DMX device? Aren't the IN and THRU wired 1...1, 2...2, etc? If so, why couldn't you have two OUTs wired to the IN? Does it need a repeater, and if so, what's the distance requirement. Surely the LOR output would produce a strong enough signal to feed two boxes at once without having to use a splitter with a power supply.

Just trying to understand why you would need a powered splitter to do this.


Reply
Macrosill
Posts: 9740
(@macrosill)
Member
Joined: 20 years ago

I believe it has to do with the signals bouncing around the cabling. I will try to get more info.


Reply
Page 1 / 2
Share: