Wireless serial mod...
 
Notifications
Clear all

Wireless serial modem

52 Posts
17 Users
0 Reactions
18.2 K Views
NogginBoink
Posts: 482
(@nogginboink)
Honorable Member
Joined: 19 years ago
FireGod wrote:Here's the problem, they don't even claim their BEST product can do more than 56,000 bps. So 57,600 bps is out of the question (I think this is the data rate used by large Renard systems). My system normally operates at 115,200 bps. Xbee claims a max rate of 250,000 bps.

Plus, most of their items are surface mount (not good for DIYers). I looked at the price of their SIP receiver at Digikey and it was $12.00 more than the Xbee Pro. The transmitter was $2.00 less. The Xbee is a transceiver.

Did I miss something here? Am I wrong? Help me out here if I missed something.

No, you didn't miss anything. You'd have to go surface mount to get the lower cost parts. I didn't realize you needed such a high baud rate either.


Reply
grages
Posts: 259
(@grages)
Reputable Member
Joined: 19 years ago

The new XBee Pro ZNet 2.5 (the old series 2) boasts a range of 1 mile (untested) and should be a drop in replacement for the series 1 units. But the series1 and the ZNet 2.5 (the old series 2) are not compatible mixed together. The non Pro 2.5 is suppose to have a range of 400 m (again untested).

FG, I know that you have tested the series 1 units, have you tried the series 2 units? I have two series one xbee's and would be interested in trying this for the renard. I also have a set of your original boards. Would a pair of these drive 1 field module? Or is there more to the FGII field modules?

Shawn

XBee Pro ZNet 2.5 (the old series 2)
http://www.digi.com/products/wireless/zigbee-mesh/


Reply
FireGod
Posts: 655
Topic starter
(@firegod)
Honorable Member
Joined: 19 years ago
grages wrote:FG, I know that you have tested the series 1 units, have you tried the series 2 units? I have two series one xbee's and would be interested in trying this for the renard. I also have a set of your original boards. Would a pair of these drive 1 field module? Or is there more to the FGII field modules?

I am not planning on testing the series 2 units.

These wireless serial modems will not work on the FGI field modules. The FGI field modules require a 5VDC power supply, zero cross signal and a RS-485 data signal.

They will supply the serial data to the FGI PC interface. You could remotley locate the PC interface board and run the cat5 cable from it to the field modules.

The boards I am getting only input/output RS-232. I have been working on a new revision that would also output RS-485 as well as RS-232.


Reply
FireGod
Posts: 655
Topic starter
(@firegod)
Honorable Member
Joined: 19 years ago
scorpia wrote:im guessing here but do i see spots for 2 voltage regulators? 1 5v and 1 3.3v?
if that is the case why not use just 3.3v?

There are two MAX232's on the board and the recommended operating conditions are from 4.5 VDC to 5.5VDC.

Also I have found the Xbee to be easy to setup and use. A DIYer needs ease of setup. Anyway I have probably burned more money than I should have just getting this far.


Reply
Posts: 919
(@scorpia)
Noble Member
Joined: 19 years ago

ah yes the good old max232.

if you wanted a single power supply it might be worth checking some of the other max units. they have quite a few that run off 3.3v and some that dont even need external capacitors.

as an example
http://datasheets.maxim-ic.com/en/ds/MAX3233E-MAX3235E.pdf

not sure how they go cost wise but maybe worth thinking about.


Reply
Page 3 / 11
Share: