Alright i remember ideas of this sort in the past being mentioned but not sure as to where...so i thought i would kinda design my own form but i am being stumped of what maybe reality or not lol.
What i want:
Before and after my light show is displaying i want to set a few props and strands of lights to be on "static".
I have figured out that i will need to make a control box basically with a DPST relay only needing the NC coil. using the data voltage/wire that will be my signal to the relay when the relay lost the data signal it will go to NC position and activate power to the static lights.
BUT i don't want the lights on 24/7 until the real show comes on so i need a timer function or a real timer...this is where i am stumped most timers i am aware of only run when there is power to them and stop the clock when there is no power to them..
The THOUGHT:
is there a timer out there that has a completely separate clock function from the 120v switching function? or is there another way?
What kind of system are you using? If it were me, using my Firegod, I would make a sequence, however long you want the lights/props on, without any music or anything (or even background music, can be cool), for that length of time, with just turning the lights/prop on you want. Then make your standard show sequences start at the end of that time. In other words, if you want your show to start at 7:00, and have the static on for an hour, start your show at 6:00, with the first sequence JUST having the lights/props you want on. That sequence would be an hour long, and the 2nd sequence would basically start at 7:00, the rest of the show. Same thing at the end - I have one sequence that I run at the end of the evening, thanking people, and letting them know the show is over. And I have the lights randomly blinking, not sequenced to anything, so they get the idea, that the show is over. Hope I explained that right. That's assuming that the lights and props, are used in your regular show.
R
51fordf2 wrote:What kind of system are you using? If it were me, using my Firegod, I would make a sequence, however long you want the lights/props on, without any music or anything (or even background music, can be cool), for that length of time, with just turning the lights/prop on you want. Then make your standard show sequences start at the end of that time. In other words, if you want your show to start at 7:00, and have the static on for an hour, start your show at 6:00, with the first sequence JUST having the lights/props you want on. That sequence would be an hour long, and the 2nd sequence would basically start at 7:00, the rest of the show. Same thing at the end - I have one sequence that I run at the end of the evening, thanking people, and letting them know the show is over. And I have the lights randomly blinking, not sequenced to anything, so they get the idea, that the show is over. Hope I explained that right. That's assuming that the lights and props, are used in your regular show.R
that is a good idea and i was kinda thinking about it but i was trying a lean away from using the computer during these "static" times and yes the static lights probably would be an hour before and an hour or so after the show.....i use RenardSS controllers
If you're looking for a digital timer, I use the Intermatic DT300CH Digital Timer. It keeps the timer/clock and settings on always (and displayed on the LCD), even when it's unplugged. I'm not positive but I believe it has an internal battery of some sort (I've had mine for 3 years and it's still operational). It will allow you to program every day of the week separately, multiple turn on and turn offs per day, 100% configurable. Overall it’s a great unit, far superior to the old-school gear driven type. I've seen guys use these types of timers to trip on a puck style high current SSR using the 110V AC signal output. I plan to use this paired configuration for my display this year.
underdog wrote:If you're looking for a digital timer, I use the Intermatic DT300CH Digital Timer. It keeps the timer/clock and settings on always (and displayed on the LCD), even when it's unplugged. I'm not positive but I believe it has an internal battery of some sort (I've had mine for 3 years and it's still operational). It will allow you to program every day of the week separately, multiple turn on and turn offs per day, 100% configurable. Overall it’s a great unit, far superior to the old-school gear driven type. I've seen guys use these types of timers to trip on a puck style high current SSR using the 110V AC signal output. I plan to use this paired configuration for my display this year.
so your going to do the same configuration like i am doing with the relay? or what way are you doing it...
so the clock works independently of its own power source(ie battery or plug) but also can switch a separate power source built off the timer function it was set to open or close? am i correct?
My plan is to power a small sub panel outside, serviced by 220V 6ga-8ga wire. Inside I'll have a 20A-40A puck style relay connected inside that will be triggered by my digital timer to the relay, and relay will be switched on by the 110V from the timer. The timer has 20 settings that can be used for turning on an off the 110V (the power required to engage my relay). This will allow me to have power shut off to the entire yard until the timer turns on.
The timer is fully digital and won't lose it's memory clock even when it's unplugged. Example: I used to get up at 4:00am, my cheap coffee pot didn't have a built in timer, so I had this turn on the coffee pot and my mancave light (small flourescent) at 3:50am and turn back off at 4:10am. Depending on my schedule I could unplug it and it wouldn't turn on the light or the coffee pot, then the following day I could plug it in and it would be right on par the next morning at 3:50am without toggling or reprogramming.
There is a manual overide button you can press to keep it on or off or in timer mode, it was just easier to yank it out of the wall when I didn't want it on.
If I understand, if you have it in your yard powered by a master switch, if you turn off the switch off your entire yard would be dark, and if you had a NC relay (with some exterior power source) the lights would be on all day except when there was signal to your relay (master switch flipped on). Your wanting to have a timer to keep the lights on from near sundown to show start, then show end to late night. No matter what you choose you'll have to have a sperate source for your prop power, even if your relay is NC, no power to the relay will be no power for the display. If you use a timer like this you can just run the timer off of a seperate line extension cord from your house to prop.
WAIT, are you wanting to use your props in your blinky-flashy display, and also statically?
I also have lights static before and after the show but at a reduced level. It’s very easy to do with the Renard controllers. You just run a sequence that sets the light levels.
My sequence is only 50mS and contains only one time cell. Vixen is configured so that it doesn’t turn all lights off automatically at the end of a sequence. So once they’re on, they’re on. An hour before the show starts, I run a sequence that slowly ramps some the lights up to a low level. Just before the show starts, I run a sequence to slowly ramp the lights down to off. Once the show is over, I run another sequence that slowly ramps some the lights up to a very low level so the lights stay on the entire night. Once the sun is up, I run a sequence that just shuts everything off.
My show computer stays on 24/7 but you could use the CMOS clock turn the PC on and have Vixen execute a program that shuts it off.
underdog wrote:My plan is to power a small sub panel outside, serviced by 220V 6ga-8ga wire. Inside I'll have a 20A-40A puck style relay connected inside that will be triggered by my digital timer to the relay, and relay will be switched on by the 110V from the timer. The timer has 20 settings that can be used for turning on an off the 110V (the power required to engage my relay). This will allow me to have power shut off to the entire yard until the timer turns on.The timer is fully digital and won't lose it's memory clock even when it's unplugged. Example: I used to get up at 4:00am, my cheap coffee pot didn't have a built in timer, so I had this turn on the coffee pot and my mancave light (small flourescent) at 3:50am and turn back off at 4:10am. Depending on my schedule I could unplug it and it wouldn't turn on the light or the coffee pot, then the following day I could plug it in and it would be right on par the next morning at 3:50am without toggling or reprogramming.
There is a manual overide button you can press to keep it on or off or in timer mode, it was just easier to yank it out of the wall when I didn't want it on.
If I understand, if you have it in your yard powered by a master switch, if you turn off the switch off your entire yard would be dark, and if you had a NC relay (with some exterior power source) the lights would be on all day except when there was signal to your relay (master switch flipped on). Your wanting to have a timer to keep the lights on from near sundown to show start, then show end to late night. No matter what you choose you'll have to have a sperate source for your prop power, even if your relay is NC, no power to the relay will be no power for the display. If you use a timer like this you can just run the timer off of a seperate line extension cord from your house to prop.
WAIT, are you wanting to use your props in your blinky-flashy display, and also statically?
no the static display will be separate from the blinky flashy Computer controlled...i just dont want time inferences to delay ...i want immediate, so static on at a programmed time(through timer) then when timer (computer timer) of display turns on, static light turn off. when timer for display turns off, static lights turn on ....i just want the static lights to have an on time and an off time and when the computer controlled display turns on it overrides the static display through the relay.
We all know that the only constant in the world is the speed of light...BUT if we assume that time is constant on the commanding computer, the only way to sync the static and animated displays without commanding both from the same clock (from the computer) means you would have to time the display down to an exact minute (the highest resolution of the digital timer, second accuracy cannot be achieved).
Quartz resonates at 60hz, nearly every clock operates based on the quartz (more than likely the digital timer is), however your computer, unbeknownst to you or me, calls up the world clock in the night or some random time during the day to reset itself to the "TRUE" time, because it gets off by <1 second per day. If your timer is on the "60hz" electrical grid or battery, both not perfect in frequency and not syncable (if that’s a word), because the grid can lead or lag small amounts it will throw off the clock small amounts throughout a week. And thus the static display would be off a few seconds by the end of a day, week, or month. I'd agree with E.Horning, just trigger it off your display computer. That will guarantee you absolutely the triggering will be on time alway's.
If that doesn't work, i'll see if I can divide by 0 and make a black hole that will throw EVERYTHING off!
I'm not clear about what you are thinking.
Forgetting about the timer for the moment, are you planning on using one DPST relay for each channel? And specifically how are you planning on creating the signal to switch the relay between the static and dynamic modes? Is that signal going to be a dedicate vixen/Renard channel, or what?
And I'm also unclear on what your problem with the timer is. If you are using a standard 24-hour timer from a hardware store, why can't you just leave it running all of the time? Do they really stop running if their output load is disconnected?

