Simple Renard Strob...
 
Notifications
Clear all

Simple Renard Strobe Burst

124 Posts
29 Users
0 Reactions
52.3 K Views
Mactayl
Posts: 2491
Guest
Topic starter
(@mactayl)
Member
Joined: 17 years ago
Slite wrote:The DC48 from AudioVisualDevices for instance

To summarise, the DC48 is a DMX input controller with 48 DC channels. Some specs:

Dual DC input (12V - 36V) (large screw terminals)
2x 20A mini blade fuses (20A overall max per 24 channels)
48 DC outputs (2A max per channel)
Output terminals arranged as V+, Ch, Ch, Ch (suits RGB)
True isolated DMX input (2x RJ45 sockets for looping)

Hi Slite,

From what I can tell it will not work with this controller unless you can supply +5 volts to the modules as I see it the DC input on that controller is setup for 12V to 36V and that would surely over drive the LED's and IC's on the module.


Reply
Posts: 53
(@fslopez1950)
Trusted Member
Joined: 16 years ago

Hi, Mac.

Is there a way to get hold of the schematic diagram of the Strobe Burst modules for I scanned the whole thread and could not find any.

Do I understand correct that it is better to use the SR 32 to control the modules because you have designed a splitter to be use for the modules?


Reply
Slite
Posts: 325
(@slite)
Reputable Member
Joined: 15 years ago
Mactayl wrote:Hi Slite,

From what I can tell it will not work with this controller unless you can supply +5 volts to the modules as I see it the DC input on that controller is setup for 12V to 36V and that would surely over drive the LED's and IC's on the module.

Ok, so if I understand you correctly... any DMX controller capable of supplying +5v can drive the pucks? And it's one channel per puck?

/Stefan


Reply
Mactayl
Posts: 2491
Guest
Topic starter
(@mactayl)
Member
Joined: 17 years ago
Slite wrote:Ok, so if I understand you correctly... any DMX controller capable of supplying +5v can drive the pucks? And it's one channel per puck?

/Stefan

Yes that is correct and you must also make sure that the controller is set up for output source and not output sink in order to turn on Q1 on the SB Module.


Reply
Mactayl
Posts: 2491
Guest
Topic starter
(@mactayl)
Member
Joined: 17 years ago
T.D.Sutton wrote:Hi Mac,

Please excuse another "New-Bie" trying to get the strobe module control straight in my head 🙁 ?? When programming in Vixen, etc, does each channel just gate the appropriate strobe module on - ie. decide at programming time how long the strobe sequence will run, and leave the module to "do it's thing", for as long as it is told to be on. Or ?? do you program a random series of "ON / OFF" blocks for the intended length of the strobes ? I suspect from the circuit that the former is the intended path, but would value confirmation 🙂

This circuit has been whirling around in my head for some time, and has come to a head recently as I have just located at a $2.00 store here a LED head band light assembly complete with 9 Hi Bright white LED's in it. Each individual LED has reflectors incorporated, all this for $2.00, it is reasonably watertight, and has a battery-box attached that could easliy house the electronics!! It certainly gives me food for thought!! 🙂

Cheers, and thanks for any comments 🙂

Terry

Hi Terry,

I attached a pdf that may explain how the SB Module works. It is controlled by Vixen as a single channel and the LED's can be turned on or off anytime in your sequence and you can ramp on or ramp off the brightness (fade) of the LED's in your sequence at anytime. When the sequence is not running the LED's are off.


Reply
caviar
Posts: 407
(@caviar)
Reputable Member
Joined: 17 years ago

Mac can these be run off renard 48 that I use for MM


Reply
Mactayl
Posts: 2491
Guest
Topic starter
(@mactayl)
Member
Joined: 17 years ago
caviar wrote:Mac can these be run off renard 48 that I use for MM

The only problem I see with running them with a 48LSD is that there is no ground line on the RJ45 coming from the controller you only have +V and 4 signals on each of the RJ45's on a 48LSD


Reply
T.D.Sutton
Posts: 445
(@t-d-sutton)
Honorable Member
Joined: 17 years ago
Mactayl wrote:Hi Terry,

I attached a pdf that may explain how the SB Module works. It is controlled by Vixen as a single channel and the LED's can be turned on or off anytime in your sequence and you can ramp on or ramp off the brightness (fade) of the LED's in your sequence at anytime. When the sequence is not running the LED's are off.

Hi Mac,

Many, many, thanks, you have confirmed what I had figured out was happening 🙂 I have used many "4017's" over the years, and they are a very usefull "Spider" to play with. 🙂

Cheers, and thanks again,

Terry


Reply
Slite
Posts: 325
(@slite)
Reputable Member
Joined: 15 years ago
Mactayl wrote:Yes that is correct and you must also make sure that the controller is set up for output source and not output sink in order to turn on Q1 on the SB Module.

Ok, to make this simple... could you please give an example of a DMX controller that could handle these? 🙂

/Stefan


Reply
Mactayl
Posts: 2491
Guest
Topic starter
(@mactayl)
Member
Joined: 17 years ago
Slite wrote:Ok, to make this simple... could you please give an example of a DMX controller that could handle these? 🙂

/Stefan

I believe a Ren 64 can do what you want using DMX


Reply
Page 6 / 13
Share: