Thanks. That's actually quite a lot for what I was looking at - I was hoping that it would be down around 5mA or lower for a controller that I'm working on.
With apologies to Phil, I am shocked.... SHOCKED I say....
I've actually never measured the current draw of a Ren-W, and all my calculations were based on spec sheets. I've had a couple other requests for this information, so I took some gear and tested it in an actual live-case. Here are the results (maximim values) in RECEIVE mode:
The Ren-W Rev6 board by itself, without an XBee module installed draws 52.8ma
The Rev6 board with a regular XBee radio installed draws 99.9ma, meaning the regular Xbee alone draws an additional 47.1ma
*** The Rev6 board with an XBee Pro radio installed draws 103.1ma, meaning the XBee Pro alone draws an additional 50.3ma
Because the Rev6 has an LED on board, you could remove it and save yourself about 10-15ma; it's not a required part.
I learned an important thing today: don't trust the manufacturers' spec sheets.
Given the size of the current draw I would start looking for conflicting GPIO pins. I have worked in mobile multi-media and sometimes when current draw is this far off you have a pin that is trying to drive high while being pulled low (or the other way around).
I will freely admit that I don't know the HW you are talking about and that this could be the current draw but often it is worth double checking the schematic.
Thanks again Dave, for doing this research.
rodb wrote:Given the size of the current draw I would start looking for conflicting GPIO pins. I have worked in mobile multi-media and sometimes when current draw is this far off you have a pin that is trying to drive high while being pulled low (or the other way around).I will freely admit that I don't know the HW you are talking about and that this could be the current draw but often it is worth double checking the schematic.
The wiki is your friend: Ren-W
(Or you could read the OP...)
Here's something new on the scene, it's a plug-in replacement for the XBee that turns your Ren-W into Wi-Fi compatible, configurable with TCP/IP, DHCP, and everything Wi-Fi. I've got a couple on order to try them out... The data sheet says the UART can handle up to 464kbps, so I'm doubting it's still fast enough for DMX... but.... it may be worth a try, who knows??? Downside? A couple bucks more than the XBPro module and so far, the only antenna option is an on-board mini-whip. The product is called the RN-XV from Roving Networks.
A couple links for you to get more info...
http://www.mouser.com/Search/ProductDetail.aspx?qs=7nsJMBTpJlzTBgzSFkpUYQ%3D%3D
http://www.sparkfun.com/products/10822
Very Cool. Could this be the answer for those of us running at 115,200??? :biggrin:
I have a real need for a couple of wireless links, but don't want to go back down to 57,600. Please let us know how it works!
rstehle wrote:Very Cool. Could this be the answer for those of us running at 115,200??? :biggrin:
I have a real need for a couple of wireless links, but don't want to go back down to 57,600. Please let us know how it works!
I should think so, although I don't know about the range... XBPros were pretty hefty in the transmitting power -- much greater than typical Wi-Fi, so we'll have to see!
dirknerkle wrote:Here's something new on the scene, it's a plug-in replacement for the XBee that turns your Ren-W into Wi-Fi compatible, configurable with TCP/IP, DHCP, and everything Wi-Fi. I've got a couple on order to try them out... The data sheet says the UART can handle up to 464kbps, so I'm doubting it's still fast enough for DMX... but.... it may be worth a try, who knows??? Downside? A couple bucks more than the XBPro module and so far, the only antenna option is an on-board mini-whip. The product is called the RN-XV from Roving Networks.A couple links for you to get more info...
http://www.mouser.com/Search/ProductDetail.aspx?qs=7nsJMBTpJlzTBgzSFkpUYQ%3D%3D
Haven't looked at the specs as I'm out on mobile, but shouldn't a uart capable of 464kbps be capable of DMX which runs at 250k?
chilloutdocdoc wrote:Haven't looked at the specs as I'm out on mobile, but shouldn't a uart capable of 464kbps be capable of DMX which runs at 250k?
That may be a peak rate with a strong tail-wind (large packet size, perhaps handshake turned off, no interference, etc). Like you, I haven't looked at the specs.
dirknerkle wrote:Here's something new on the scene, it's a plug-in replacement for the XBee that turns your Ren-W into Wi-Fi compatible, configurable with TCP/IP, DHCP, and everything Wi-Fi. I've got a couple on order to try them out... The data sheet says the UART can handle up to 464kbps, so I'm doubting it's still fast enough for DMX... but.... it may be worth a try, who knows??? Downside? A couple bucks more than the XBPro module and so far, the only antenna option is an on-board mini-whip. The product is called the RN-XV from Roving Networks.A couple links for you to get more info...
http://www.mouser.com/Search/ProductDetail.aspx?qs=7nsJMBTpJlzTBgzSFkpUYQ%3D%3D
Dave, Is this not the same device just with an SMA connector? http://www.mouser.com/Search/ProductDetail.aspx?qs=sVdVlwbC4Qh2F3Icf20%2fXA%3d%3d
(It was under the "Customers Who Bought This Item Also Bought" section :biggrin2:)


