Renard-WC Wireless ...
 
Notifications
Clear all

Renard-WC Wireless Controller

266 Posts
47 Users
0 Reactions
119.3 K Views
rstehle
Posts: 4348
(@rstehle)
Illustrious Member
Joined: 19 years ago
Could have been a joint

Huh............. :grin::grin: (I grew up in California in the 60's & 70's..........)


Reply
dirknerkle
Posts: 10310
Topic starter
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
rstehle wrote:Huh............. :grin::grin: (I grew up in California in the 60's & 70's..........)

OOoooooo....like...., WOWWwwwwwww, mannnnnn...... 😆


Reply
ErnieHorning
Posts: 4434
(@erniehorning)
Famed Member
Joined: 19 years ago
IdunBenhad wrote:That's really great that you got your brother going. One to sequence and one to do the hardware. COOL, man.Hmmmm.... a real future in management! 😎

Now if he can get his brother the do both, he'd be the CEO material!:p


Reply
Posts: 3277
 Jrd
(@jrd)
Famed Member
Joined: 19 years ago
rstehle wrote:Huh............. :grin::grin: (I grew up in California in the 60's & 70's..........)

Not that kind of joint, lol. 😆

ErnieHorning wrote:Now if he can get his brother the do both, he'd be the CEO material!:p

Lol, but I like the soldering. 🙂 And I don't think he would like it very much.


Reply
IdunBenhad
Posts: 1603
(@idunbenhad)
Noble Member
Joined: 18 years ago

Hi:
A cold joint results when you run out of matches.


Reply
gdyrdave
Posts: 916
(@gdyrdave)
Noble Member
Joined: 16 years ago

Dirk,
I am having a great deal of trouble getting these ren6 boards to communicate to the outside world. I am able to change the baud rates etc, but the recieved data is not right. I set up a ren6 to the computer as per the wiki, but the data I am getting back is not correct. Looking at the boards, it appears that I can use the 6 as a setup platform. The response I get back is XZy. No matter what baud rate, Parity, Stop bit I change to, it comes up jibberish. They do communicate, its just the rs232 output is wrong for some reason. Any ideas, or do you need more info. I am willing to send these populated boards to you if you are willing to check them out. I have tried everything I know to solve the problem, but what do I know...LOL. Need your help my friend. Thanks

Dave


Reply
dirknerkle
Posts: 10310
Topic starter
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

Mighty strange.... let me check them out for you. I'll PM my address

-dave


Reply
gdyrdave
Posts: 916
(@gdyrdave)
Noble Member
Joined: 16 years ago

Great...Thanks alot Dave. One is set at 1200 baud, so I can see the output on my slow o'scope. The other is set at 57.6. Do appreciate this.

Dave


Reply
dirknerkle
Posts: 10310
Topic starter
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
gdyrdave wrote:Great...Thanks alot Dave. One is set at 1200 baud, so I can see the output on my slow o'scope. The other is set at 57.6. Do appreciate this.

Dave

You do know that for them to communicate they must be set to exactly the same params, right?


Reply
gdyrdave
Posts: 916
(@gdyrdave)
Noble Member
Joined: 16 years ago

Of course. I just set the one so I could see the data better on my slow scope. I had them set to the exact same parms. The reciever was transmitting data to the controller but obviously not correct. I was just doing the at commands with the slow one. was getting a response but not the correct one. I looked at the data, thought it may have been inverted. Not even close. So therefore I am assuming the data is not correct for the SS24 controller. I even tried the 2 Rev6's between 2 computers. Not good. I looked at the pc board and the data in and out goes directly to the Max232. Then with jumpers To the connector. I have been playing with this for over a week now. I guess my limited knowledge and old age contribute too...LOL... But we are having fun. Got interested in the about 8 or 10 years ago when I saw a video on the internet where a house was lit up with the Wizards of Winter. Thought they did it with midi. DUH


Reply
Page 23 / 27
Share: