Just wondering why not use a DCSSR but only populate for the 3 channels? Note that the OPTO's are actually available in 4 pin versions, so you would only put three into the board.
That being said, I've got a decent bag of RJ11 jacks kicking around here. :biggrin:
i actually like the concept of a breakout board.....3 RJ45s in 4 RJ11s out.....would eliminate all the need for special controller...would it not?
It would allow the use of the REN48, if needed like me, and to use a 12v input to this DCSSR design so I do not have to be dual voltage on the REN48. I run 12v floods and the other DCSSR's require 5 volts and has 4 channels (need to group in 3's to not waste any channels..ie 4 channels @ 3 DCSSR's = 12 channels). Also keeps cabling standardized so I do not have to make a bunch of lonj rj11 cables, maybe a few jumpers. Just a thought.
AFAIK DCSSRs can run on 12v logic levels (this is the logic side, not the output side) -- sorry for the hijack...
If you are using the Ren48LSD to drive the DCSSR Version 2.4, YOU MUST HAVE THE Ren48LSD CONFIGURED TO SEND 5V TO THE DCSSR. IF THE Ren48LSD IS SENDING ANY OTHER VOLTAGE, YOU MUST CHANGE RESISTORS 9-13 TO DIFFERENT VALUES
FROM THE WIKI...
What would these values be to not overheat existing design as I have read?
I know this is off topic
At this point in time I am open to all suggestions which includes existing hardware (LabRat's DCSSR, Ren48LSD, Simple Renard 32 or Simple Renard RGB+W) So keep the ideas coming.
Mactayl wrote:At this point in time I am open to all suggestions which includes existing hardware (LabRat's DCSSR, Ren48LSD, Simple Renard 32 or Simple Renard RGB+W) So keep the ideas coming.
Psshhh... get the boards made. (at least a 10 board sample from the likes of Seeed (or the new vendor)). It's fun to be creative. I was just wondering if there was a specific shortcoming in the existing boards. (Other than the color :cool2:) Go for it!! (and take pictures)
LabRat wrote: I was just wondering if there was a specific shortcoming in the existing boards.
No not at all, every board I mentioned are excellent boards and can do the job,, I was approached by a DIYC member wanting a controller dedicated just for LED Strips so I came up with an idea of what he was looking for then see what kind of interest there might be for them.
duramadmax wrote:FROM THE WIKI...What would these values be to not overheat existing design as I have read?
I know this is off topic
/ContinuedHijack
Just to close on this:
12v - Vf (1.6v) = 10.4v across the 680 ohm resistor equates to 15.3mA and 159mW - the opto supports up to 60mA. An 1/8W would not be a good choice but a 1/4W should be OK - it's a bit on the high side but should work ok. You can definitely stick with 680 ohm but may want to pop in 1/2W resistors but again 1/4W should work also...
If you want to go with the original design spec, then put in 2K resistors - this equates to 5.2mA and 54mW so an 1/8 or 1/4W resistor is fine. I'll update the Wiki to clarify this...
edit - - Wiki has been updated...
/EndHijack
Mactayl, I would definitely be interested in your 48 channel design. It would be perfect for the display element I want to build this year. I'm not an electrical engineer so I can only critique a trivial matter of your design. Your channel numbering is messed up for channels 7-9 and 10-12.
plasmata wrote:Mactayl, I would definitely be interested in your 48 channel design. It would be perfect for the display element I want to build this year. I'm not an electrical engineer so I can only critique a trivial matter of your design. Your channel numbering is messed up for channels 7-9 and 10-12.
Thanks for the keen eye,, it is now changed in post #17
