I'm not aware of any pixel boards that would connect to the Renard 32 plus. What pixel boards do you have?
Skunberg wrote:I'm not aware of any pixel boards that would connect to the Renard 32 plus. What pixel boards do you have?
The one this thread is about will. (The PX1)
lmercor wrote:Hello to all.Not sure if this is the correct forum to post my question.
I have a pixel controller but i'm having trouble setting it up.
I have a renard controller (Renard 32 Plus), Vixen 3.x and the pixel controller. I have the pixel controller after the renard 32 plus chained to it. When vixen starts, all the pixels (WS2811) start to flash ramdomly without any sequence or anything programmed on vixen, just the controller set up there., Then I have created differents test scenarios on Vixen, but none of them will work on the pixels.
Is there a way to test the Pixel Board. to make sure the program on the microcontroller is OK. I have programmed the PIC using a JDM programmer and a pic programmer PICPGM. I have 3 pixel boards and all of them do the same. Is there something I'm missing or a configuration I'm not doing.
A little help will be much appreciated.
Thanks
Luis
Have you tried connecting it to your computer w/out the Renard 32 plus?
Where on the Ren 32 are you plugging in the PX1?
I have tried but the result is the same, all the pixels flash randomly. What I have noticed on Vixen 3 is that using the other Renard Boards 32 plus, whenever Vixen 3 starts the RX led stars flashing like receiving information even tough the lights stays off. I tried the pixel boards directly to the computer and the result is the same, and also the FE led stays on most of the time. Will do some test with vixen 2.x
algerdes wrote:Where on the Ren 32 are you plugging in the PX1?
the Ren 32 plus has two connectors RX and TX, the Pixel board goes into the TX connector. I actually have two Ren 32 Boards and I have used both in the past chain to each other to have more channels to control.
lmercor wrote:and also the FE led stays on most of the time.
Do you have the baud rates correct? Sounds like you might have a mismatch.
For now, ignore the pixels flashing. You need to deal with the FE conditions first. That is the more fundamental problem, and fixing that should also fix the flashing pixel problem. If it doesn't, then there is a second problem that can be dealt with later on.
The first things to check is that the PX1 is set for the same baud rate as the REN32, that the jumpers relating to communications on the PX1 are correct, and that the cable between the Ren32 and the PX1 is good. Also, double-check the solder joints on the PX1, and take a look inside the RJ45 jack to make sure that there aren't any bent or dislodged pins.
P. Short wrote:For now, ignore the pixels flashing. You need to deal with the FE conditions first. That is the more fundamental problem, and fixing that should also fix the flashing pixel problem. If it doesn't, then there is a second problem that can be dealt with later on.The first things to check is that the PX1 is set for the same baud rate as the REN32, that the jumpers relating to communications on the PX1 are correct, and that the cable between the Ren32 and the PX1 is good. Also, double-check the solder joints on the PX1, and take a look inside the RJ45 jack to make sure that there aren't any bent or dislodged pins.
I will check on that. I have changed the settings on the asm file to match the baud rate and then built it again to generate the hex. I'm using a JDM programmer and PICPGM to program the microcontroller not the PICKIT as recommended on the main pixel PX1 page. I will check the asm again, and check the conf word for the PIC at the time of programming.
Thanks for the tips
I will let you know the result.
Thanks
Luis
P. Short wrote:For now, ignore the pixels flashing. You need to deal with the FE conditions first. That is the more fundamental problem, and fixing that should also fix the flashing pixel problem. If it doesn't, then there is a second problem that can be dealt with later on.The first things to check is that the PX1 is set for the same baud rate as the REN32, that the jumpers relating to communications on the PX1 are correct, and that the cable between the Ren32 and the PX1 is good. Also, double-check the solder joints on the PX1, and take a look inside the RJ45 jack to make sure that there aren't any bent or dislodged pins.
What programmer do you use to program the PIC?
Thanks
PicKit2 or PicKit3 from Microchip. I have one of each.
