algerdes wrote:To all that have had a hand in this wonderful piece of hardware and firmware - THANK YOU.
This is going to fit in perfectly with the show that we are trying to expand.The big question is this:
We have 14 Renard SS24s, all with the DMX firmware onboard, and several other Renard units (DC) that would be in the data stream. (I believe they also have DMX firmware.) Note that I believe they are all set to DMX Channel 1. These have worked together for 4 years now, one long data line, without a problem.Can this PX1 be put at the end, or even in the middle, of that string? If so, what do we need to do special to make it work with its older brothers?
I freely admit I don't know as much about the Renard system that I should, but so far luck has been on my side.Thank you for your input.
Unfortunately there is no DMX firmware for the PX-1 and no plans to write DMX firmware so you will have to run a separate network for Renard protocol. If you were running on a Renard data stream, they would work fine together, although you may run into channel limitations(if they were on the same stream) depending on how many pixels you run with all those normal channels.
Thanks Jrd.
This confirms that I'm switching to use E1.31 from the computer to a central point. DIYLEDExpress E1.31 bridge has 6 outputs, which I believe I can be set for each of the different protocols at the same time. Renard-DMX off of two of them, a DMX line from a third (I have some actual theatre DMX lights) and then the other 3 set to Renard (Non-DMX) to drive the PX1s.
For the new big trees I'm going to have to invest in a E6804 (or E682).
algerdes wrote:Thanks Jrd.This confirms that I'm switching to use E1.31 from the computer to a central point. DIYLEDExpress E1.31 bridge has 6 outputs, which I believe I can be set for each of the different protocols at the same time. Renard-DMX off of two of them, a DMX line from a third (I have some actual theatre DMX lights) and then the other 3 set to Renard (Non-DMX) to drive the PX1s.
For the new big trees I'm going to have to invest in a E6804 (or E682).
Yes I believe you are correct and that sounds like a good solution for you!
algerdes wrote:Thanks Jrd.This confirms that I'm switching to use E1.31 from the computer to a central point. DIYLEDExpress E1.31 bridge has 6 outputs, which I believe I can be set for each of the different protocols at the same time. Renard-DMX off of two of them, a DMX line from a third (I have some actual theatre DMX lights) and then the other 3 set to Renard (Non-DMX) to drive the PX1s.
For the new big trees I'm going to have to invest in a E6804 (or E682).
If going to use an E6804 or E682, why not use the E1.31 out to the E68x controller and use that as your bridge to your DMX and Renards? You can configure outputs from the E68x controllers for those protocols and eliminate the need for the bridge? Then all of your traffic is output on the single E1.31 connection from the PC to the controller, then distributed from there? Even use standard wireless routers to eliminate any cabling between the PC and the controller as well and also eliminate any need for direct wiring between the PC and controller.
I would lean towards the E682 as well if doing something like this, having 16 fused outputs from the controller vs 4 from the E6804 is definitely beneficial, especially if looking at a mega tree.
There is a million ways to do this, just an option you can also look at.
Thanks for that heads up. I have yet to look at all the capabilities of the E682. Just know from conversations here (and other sites) that it is the "way to go" for a large number of pixels in an area [such as in a megatree].
I am having trouble building the Hex code for the PX1. i keep getting errors. I attached the error code text document. i am using MPLAB IDE 8.92
sparky588 wrote:I am having trouble building the Hex code for the PX1. i keep getting errors. I attached the error code text document. i am using MPLAB IDE 8.92
If your PICs are blank then please try following boyelroy's guide to programming the 16F1825: http://doityourselfchristmas.com/forums/showthread.php?32618-Programming-the-16F1825-in-the-PX-1
If your PICs came pre-programmed from the Group Buy, it may be easier to use bolwire's PX1 setup application: http://doityourselfchristmas.com/forums/showthread.php?32557-Ren-PX1-Setup-application&p=325600#post325600
sparky588 wrote:I am having trouble building the Hex code for the PX1. i keep getting errors. I attached the error code text document. i am using MPLAB IDE 8.92
While some of the errors are tough to decipher, this one "Directive only allowed when generating an object file" indicates you did not follow the MPLAB setup / build instructions for the PX1 properly or you modified the code. It is likely that the rest of the errors are from similar issues. I suggest you start with clean project and code and try again.
BTW: I also like MPLAB 8.92 much better than MPLAB X.
Martin
Just downloaded and built using mplab 8.92. I only got the expected warnings
Debug build of project `H:\Users\mmueller\Documents\Projects\PX1\px1.mcp' started.Language tool versions: MPASMWIN.exe v5.51, mplink.exe v4.49, mplib.exe v4.49
Preprocessor symbol `__DEBUG' is defined.
Mon Jun 09 09:35:24 2014
----------------------------------------------------------------------
Clean: Deleting intermediary and output files.
Clean: Deleted file "H:\Users\mmueller\Documents\Projects\PX1\px1.mcs".
Clean: Done.
Executing: "H:\Program Files (x86)\Microchip\MPASM Suite\MPASMWIN.exe" /q /p16F1825 "renard-px1a_20130629_1374258537.asm" /l"H:\Users\mmueller\Documents\Projects\PX1\Output\renard-px1a_20130629_1374258537.lst" /e"renard-px1a_20130629_1374258537.err" /o"renard-px1a_20130629_1374258537.o" /d__DEBUG=1
Message[303] H:\USERS\MMUELLER\DOCUMENTS\PROJECTS\PX1\RENARD-PX1A_20130629_1374258537.ASM 171 : Program word too large. Truncated to core size. (DFA4)
Message[303] H:\USERS\MMUELLER\DOCUMENTS\PROJECTS\PX1\RENARD-PX1A_20130629_1374258537.ASM 174 : Program word too large. Truncated to core size. (D9FF)
Warning[219] H:\USERS\MMUELLER\DOCUMENTS\PROJECTS\PX1\RENARD-PX1A_20130629_1374258537.ASM 371 : Invalid RAM location specified.
Warning[219] H:\USERS\MMUELLER\DOCUMENTS\PROJECTS\PX1\RENARD-PX1A_20130629_1374258537.ASM 392 : Invalid RAM location specified.
Warning[219] H:\USERS\MMUELLER\DOCUMENTS\PROJECTS\PX1\RENARD-PX1A_20130629_1374258537.ASM 448 : Invalid RAM location specified.
Message[305] H:\USERS\MMUELLER\DOCUMENTS\PROJECTS\PX1\RENARD-PX1A_20130629_1374258537.ASM 503 : Using default destination of 1 (file).
Warning[219] H:\USERS\MMUELLER\DOCUMENTS\PROJECTS\PX1\RENARD-PX1A_20130629_1374258537.ASM 712 : Invalid RAM location specified.
Warning[219] H:\USERS\MMUELLER\DOCUMENTS\PROJECTS\PX1\RENARD-PX1A_20130629_1374258537.ASM 1937 : Invalid RAM location specified.
Warning[202] H:\USERS\MMUELLER\DOCUMENTS\PROJECTS\PX1\RENARD-PX1A_20130629_1374258537.ASM 2275 : Argument out of range. Least significant bits used.
Message[303] H:\USERS\MMUELLER\DOCUMENTS\PROJECTS\PX1\RENARD-PX1A_20130629_1374258537.ASM 2383 : Program word too large. Truncated to core size. (DFA4)
Message[303] H:\USERS\MMUELLER\DOCUMENTS\PROJECTS\PX1\RENARD-PX1A_20130629_1374258537.ASM 2383 : Program word too large. Truncated to core size. (D9FF)
Executing: "H:\Program Files (x86)\Microchip\MPASM Suite\mplink.exe" /p16F1825 "..\renard-px1a_20130629_1374258537.o" /u_DEBUG /z__MPLAB_BUILD=1 /z__MPLAB_DEBUG=1 /m"px1.map" /w /o"px1.cof"
MPLINK 4.49, Linker
Device Database Version 1.14
Copyright (c) 1998-2011 Microchip Technology Inc.
Errors : 0
MP2HEX 4.49, COFF to HEX File Converter
Copyright (c) 1998-2011 Microchip Technology Inc.
Errors : 0
Loaded H:\Users\mmueller\Documents\Projects\PX1\Output\px1.cof.
----------------------------------------------------------------------
Debug build of project `H:\Users\mmueller\Documents\Projects\PX1\px1.mcp' succeeded.
Language tool versions: MPASMWIN.exe v5.51, mplink.exe v4.49, mplib.exe v4.49
Preprocessor symbol `__DEBUG' is defined.
Mon Jun 09 09:35:26 2014
----------------------------------------------------------------------
BUILD SUCCEEDED
Hello to all.
Not sure if this is the correct forum to post my question.
I have a pixel controller but i'm having trouble setting it up.
I have a renard controller (Renard 32 Plus), Vixen 3.x and the pixel controller. I have the pixel controller after the renard 32 plus chained to it. When vixen starts, all the pixels (WS2811) start to flash ramdomly without any sequence or anything programmed on vixen, just the controller set up there., Then I have created differents test scenarios on Vixen, but none of them will work on the pixels.
Is there a way to test the Pixel Board. to make sure the program on the microcontroller is OK. I have programmed the PIC using a JDM programmer and a pic programmer PICPGM. I have 3 pixel boards and all of them do the same. Is there something I'm missing or a configuration I'm not doing.
A little help will be much appreciated.
Thanks
Luis
