Raspberry PIxel dri...
 
Notifications
Clear all

Raspberry PIxel driver.

128 Posts
25 Users
0 Reactions
46.5 K Views
Barnabybear
Posts: 1583
Topic starter
(@barnabybear)
Noble Member
Joined: 15 years ago
ronp5683 wrote:
So I am open to the idea of either doing an SPI or E1.31 bridge to drive WS2801 strings, DMX, serial, etc. I think I can mange to make each output type programmable under software control. Firmware updates would allow future changes for other formats. Does this interest you?

Yes, and thanks to you and others for the intrest.

Long day again - so just a quick post (I'll do better tomorrow).

I don't know how you guys are viewing the PI and diy blinky flashy.

My thoughts are: That the E68x (I have 2 E681's) are brilliant - it does what it says on the box and comes with some of the best support I've ever come across (most people would not bother offering upgrades to existing customers - the E681 upgrade to 6 universes - they would just say buy an E682).

Where does the PI fit in? It's cheap, it has USB ports so if you stick a WIFI dongle in one it's wireless, it has a useable memory and (although it has hardware limitations) can do anything that someone can program.

So where do we go? Where ever you want to! The options are endless - stand alone pixel tree interface (that has short sequences stored on the SD card that can be called up via a single channel and output 8 universes via E1.31 to your other controllers). A WIFI fed controller on the roof running your ridge pixels (not to meny and all the same type). A stand alone controller for your lights that you can access via a URL on your phone as your BBQing in your garden. Having singing faces by the side of the road that are motion activated. Video called from a single E1.31 channel has been done all ready.

So I'm up for whatever you are - In general it would be cool to have 'a PI' and then insert the interface you require, down load the software and display. I think it place in the Blinky Flashy world is that it does the stuff, that all the other stuff doesn't do.

I think that the board is so versatile that many projects will be based on it (or simalar) and would like people to consider this during the development.

Tonights update - the PI is driving WS2801 pixels over WIFI (the only things connected to the board are - pixels, 5V and a WIFI dongle). I can use my phone (connected to my home network) to access a URL and from that set the colours for each channel. Again not ground breaking - but when we get DMX insted of pixel out of the SPI, thats the garden lighting sorted.


Reply
Posts: 238
(@ronp5683)
Reputable Member
Joined: 14 years ago

Cavet,

The SPI port is fast enough to drive say 24 SPI channels being multiplexed, which is equivalent to 24 universes. So this is much cheaper, and you get more ports. For me, I like the idea of using one universe per item for the lights. It makes the wiring easier. Since universes are expensive, you have to daisy chain the lights. However, you can't currently use the SPI to drive the old DMX stuff.

The overhead in the Ethernet is about 50 bytes for the Ethernet/IP/UDP pack, 124 or so bytes for the E1.31 overhead. So with 512 bytes of real data at best the overhead is 25 percent. So I would suspect that the SPI has less overhead, but you can not run it as fast.

Typical universe bandwidth = 512 bytes * 8 Bits * 20 times a second (50mS) = 82Kbaud. Or about 12 universes per 1Mbit.


Reply
Posts: 238
(@ronp5683)
Reputable Member
Joined: 14 years ago

Barnabybear,

I like the PI also, cause I think Linux is a better real time system than Windows. I have been breaking into your form thread, because I have been mulling over what to do for next year. I know that I can do a pretty cheap SPI expansion, but I am doing this just to help out. Still not sure that this is where I want to go.

I don't know how things work on the forum. I don't mind doing the design, but I don't want to spend the next 10 years supporting it. Is there a group that will take over designs and do the orders?

Also, the parts I tend to pick are not very good for the home experimenter. The parts are 0.8 mm or 0.5 mm pitch. I would not want most people trying to solder these, including myself. Anyway I am willing do a prototype, and send it to you for verification. If you are going to support this you will need a $12 programmer off e-bay. The software is free.

EPM3032ATC44-10 $1.40 at 0.8 mm pitch (supports 12 SPI outputs) could just use two of these
EPM3064ATC100-10 $3.10 at 0.5 mm pitch (supports 24 SPI outputs)


Reply
Posts: 35
(@snunn)
Eminent Member
Joined: 17 years ago

Finally got my raspberry pi up and running with all the tools built/installed for using spi with java and python. I also built a little demux circuit so that I can test out routing SPI. Now if my lights would just show up in the mail.


Reply
Posts: 35
(@snunn)
Eminent Member
Joined: 17 years ago

I have tried various demo's of controlling the LEDs but all I can ever seem to accomplish is some random flashing at best. Has anyone else had any luck?


Reply
Page 9 / 26
Share: