n8huntsman wrote:I wish I was as smart as you guys. It really amazes me when I read this stuff even though I don't really understand it. So what exactly will this thing do? I get the part about having the controller far away from the start of the strings but what's with the 24v stuff? How would that be used?
There were two basic ideas that could have gone with. The first, the controllwer could have just extended the distance from the controller (provide the data lines), and no power. Then you would have had to have a seperate power supply at start of each pixel string. It would make this controller much simpler and cheaper, but it would require a lot more planning on how to route the power.
The second option, the one I am pursuing, it to supply power along with the data. The idea is that you supply power to the controller board, say the E680, and it passes the power and the data down the line to the pixel string. I have a few strings of 5 VDC pixel strings (the GE Color Effects light), and then 12 VDC is the other common voltage of pixel strings. I plan on making this controller support both 5 and 12 VDC, but right now I am concentrating on 5 VDC (I am hoping it should be a simple as replacing the receiver voltage regulator that outputs 12 VDC instead of 5 VDC, and any support components, caps, etc).
The reason for 24 VDC is there will be a voltage drop when running the power down the extended lines. After the voltage drop, there would not be enough power to run the strings. The solution was to run higher voltage, and convert it down when it is close to the string. Here is a rough diagram:
24 VDC Input --> E680 Controller --> Transmistter --> Receiver --> Pixel String
24 VDC 24 VDC 24 VDC --> 5 VDC
I hope that explains it better.
Erik
This is probably not the best place for this but here goes. I got some 2801 strings and then looked and the wires are not labeled. I got this info from Jim St. John and passing it on.
There are never any guarantees, color coding can and does change from batch to batch. Having said that, the last batch of 2801s I received were red, white, green, and blue as follows:
RED +5V
WHT GND
GRN CLK
BLU DATA
If in doubt, hooking up a single pixel is a good way to double-check. The important thing is to have +5V and ground correct. If you swap clock and data, it won't work but it won't hurt anything.
Another check, depending on how well you can see the internal wire connections of the pixels, both power and ground will have their 'in' and 'out' wires connected to the same point, whereas data and clock will have separate connection points in the pixel for in and out.
You might also post this on the forum, as others may have the same pixels you have.
intwoit2002 wrote:This is probably not the best place for this but here goes. I got some 2801 strings and then looked and the wires are not labeled. I got this info from Jim St. John and passing it on.There are never any guarantees, color coding can and does change from batch to batch. Having said that, the last batch of 2801s I received were red, white, green, and blue as follows:
RED +5V
WHT GND
GRN CLK
BLU DATAIf in doubt, hooking up a single pixel is a good way to double-check. The important thing is to have +5V and ground correct. If you swap clock and data, it won't work but it won't hurt anything.
Another check, depending on how well you can see the internal wire connections of the pixels, both power and ground will have their 'in' and 'out' wires connected to the same point, whereas data and clock will have separate connection points in the pixel for in and out.
You might also post this on the forum, as others may have the same pixels you have.
You are correct in that there are variants to the color coding. I have several strings of 2801's and some of them use the above color code, and some use this
RED +5V
BLUE DATA
WHITE CLOCK
BLACK GND
The IN and OUT side to the wires are not marked, but from my observations the IN has always been on the side where the IC is soldered to the pixel PC board.
If in doubt, check with the pixel supplier for the hookup data sheet. If you get them from Ray Wu he will email you the hookup diagram if you ask him.
David_AVD wrote:
The transmitter side is probably fine. The problem with the regulator on the right is that it will be dropping 19V @ whatever current the pixels draw. That's 19W of pure heat (and 19W power wasted) for just 1A of output! As n1ist says, use a switching regulator to get the high efficiency (and low heat) you need.
It's moot at this point since a switcher is already in here, but just for future reference - In addition to significantly reduced efficiency, a linear regulator negates most of the advantages of power transmission at 24v, since Iin = Iout. With the switcher, Iin = Iout*(5/24)/(regulator efficiency) - e.g. significantly less than Iout.
Thanks for the help everyone. I am back to working on this (life got in the way for a bit). I put in a mouser order to prototype a few of these. I added a few extra parts, and different parts to play with. I will post progress, and pictures as I actually get something working. I need to update the schematic I have posted.
Thanks,
Erik
