NRF24L01 - eagle la...
 
Notifications
Clear all

NRF24L01 - eagle layout?

60 Posts
11 Users
0 Reactions
36.7 K Views
LabRat
Posts: 2981
Topic starter
(@labrat)
Famed Member
Joined: 17 years ago
n1ist wrote:On the schematic, the power pins on the 75179 look like they will auto-connect to Vcc and Gnd, not to VCC_ISO and GND_ISO. Likewise, the RJ45s should connect to GND_ISO.

Also, something is wrong with the named nets in the power supply; it looks like you have Vcc on both sides of IC2 (actually, since the connection dot on the positive end of C4 is missing, you have no named net on the output of IC2, and C4 is connected from Vcc to GND)

/mike

I'm still blurry eyed, but as soon as you said GND to the RJ45 I realized ... OMG (Goodness)... absolutely right. Thanks for the second set of eyes, and I'll be going over all of these observations tonight.

  • 75179 - Initially auto-connected, but this was overridden. The VCC/GND connections are just below it on the schematic.
  • Missing dot on C4 - Yes, dot is missing, but connection is/was made. So function is correct.
  • VCC connecting to output of IC2 - purely an eagle "symbol" artifact. The symbol had a label VCC, but the net is named 3.3V. That's part of the schematic clean-up that is still required.
  • RJ45 to GND connection - very good catch:cool2:, and one I would have missed (and has me wondering if I did that wrong in a previous design (Edit: Nope)).

A


Reply
LabRat
Posts: 2981
Topic starter
(@labrat)
Famed Member
Joined: 17 years ago

Another round, and I think this one is ready to go to the fab shop. I've also tried to make a very small NRFRGB receiver. Again this is primarily SMD. Not sure if I will go ahead with this, or rework to fit inside the 5cmx5cm board limit at SeeedStudio (and other board shops). Any thoughts from those who get smaller/odd shaped board done ? Where do you go to get them panelized?

DMX to NRF 4

and the new board (same width as the NRF module, but a little over twice as long.

NRF 3CHAN

Reply
timon
Posts: 2149
(@timon)
Noble Member
Joined: 16 years ago

If your dumping Renard add the option for one more opto so you can control transmit/receive then you could add RDM. Now you can remote program the device.


Reply
LabRat
Posts: 2981
Topic starter
(@labrat)
Famed Member
Joined: 17 years ago
timon wrote:If your dumping Renard add the option for one more opto so you can control transmit/receive then you could add RDM. Now you can remote program the device.

RDM isn't absolutely required for remote programming. That being said, that last version of the PCB had two opto's so that Tx and Rx are both isolated. (Mind you.. each to it's own RJ45, so not quite as a "bus"). I've spent the evening grabbing some of my previous designs using RFM12B modules, and replacing with NRF24L01's. Here's a board that fits within the 5x5cm SeeeStudio footprint. The actual footprint measures 3.5cm x 4.1 cm, so I should be able to get 10 boards for $10.00 .

NRF 3CHAN SQUARE

Reply
LabRat
Posts: 2981
Topic starter
(@labrat)
Famed Member
Joined: 17 years ago

Woah... it's been a while, but I just found out that SeeedStudio has changed their PCB offerings. It's now $10.00 for only 5 pcb's, not 10. That's a pretty stiff price hike. Time for me to search around again, to see what others are offering proto-typing services.

[EDIT] Hmmm.. ITead still has 10 boards for $10. I'm guessing that's where my next order will go.


Reply
LabRat
Posts: 2981
Topic starter
(@labrat)
Famed Member
Joined: 17 years ago

Another "ah-hah" moment in the schematic. While reviewing the USB2DMX I found a note that indicated I had originally missed having a pull-up on the outputs of the 6N137 opto-isolator. Sure 'nuff, I had repeated the mistake in this design as well. Just recording this here, so that others may also learn from my mistakes. :biggrin:


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

Here's something similar that I'm playing around with. The board is mis-named (it has nothing to do with Renard), but it's a 2-channel controller using a PIC16LF1503 and the usual nRF24L01A module. I'm just getting around to checking it out, hence the large number of un-installed components and sockets.

renard2

Reply
LabRat
Posts: 2981
Topic starter
(@labrat)
Famed Member
Joined: 17 years ago

**DRAT YOU MURPHY!!!**
(With that out of the way)

I have a SNAFU with my PCB (Of course I discovered it 4 hours after getting the "it's now in production" email.. (sigh)). For reasons that I can't recall I thought the PIC I choose was available in a wide bodied SOIC (aka 300mil) package. It turns out that it is only available in a package that is only 150mil wide. So.. clearly my pads are going to be too far apart. The question now is... how hard would it be to try and barnacle the PIC into place, or do I simply write it off and order up another set of boards.

It's at most 10 boards.. so any suggestions on methods to barnacle across the gaps?


Reply
kingofkya
Posts: 2165
(@kingofkya)
Noble Member
Joined: 15 years ago

I have done worse. just get soem tiny mod wire and and a pointy tip. 30 awg size stuff works great for smd

http://www.jameco.com/webapp/wcs/stores/servlet/ProductDisplay?langId=-1&storeId=10001&catalogId=10001&pa=22631&productId=22631&keyCode=WSF&CID=GOOG&gclid=CMTE4oaVrr0CFcWTfgodIwkA1A


Reply
LabRat
Posts: 2981
Topic starter
(@labrat)
Famed Member
Joined: 17 years ago

Do you recommend centering the part and tacking every pin with an ultra-short piece of wire, or aligning with one side with the pads, and then tacking down with longer strands. (Did that make sense?)


Reply
Page 4 / 6
Share: