New project: Sawyer...
 
Notifications
Clear all

New project: Sawyer Star (LED array)

54 Posts
13 Users
0 Reactions
33.2 K Views
Matt_Edwards
Posts: 2664
(@matt-edwards)
Famed Member
Joined: 18 years ago

Re: New project: Sawyer Star (Charlieplexed LED array)

as a first hack, the Attached should work for a 8x8 matrix.

DMX16DCSSR Mod1

Reply
Matt_Edwards
Posts: 2664
(@matt-edwards)
Famed Member
Joined: 18 years ago

Re: New project: Sawyer Star (Charlieplexed LED array)

How many LEDs are needed? Are we going to keep them single colour or go to 4 pin RGB LEDs.
If we go RGB, the matrix size will be 6x8 (18 LEDs) or 9x8 (24 LEDs)

Cheers


Reply
dmcole
Posts: 2196
Topic starter
(@dmcole)
Noble Member
Joined: 19 years ago

Re: New project: Sawyer Star (Charlieplexed LED array)

Matt_Edwards wrote:How many LEDs are needed? Are we going to keep them single colour or go to 4 pin RGB LEDs.
If we go RGB, the matrix size will be 6x8 (18 LEDs) or 9x8 (24 LEDs)

The Thorpe star has 25 Blue, 15 Green and 20 Red with the provision for a single RGB LED (either common cathode or common annode) in the center.

\dmc


Reply
dmcole
Posts: 2196
Topic starter
(@dmcole)
Noble Member
Joined: 19 years ago

Re: New project: Sawyer Star (Charlieplexed LED array)

Just an update: Matt is drawing up a new schematic, based on RPM's DMX16 design. After I review it, I'll order up the components from Mouser and build a bread-board version tout de suite.

\dmc


Reply
Matt_Edwards
Posts: 2664
(@matt-edwards)
Famed Member
Joined: 18 years ago

Re: New project: Sawyer Star (Charlieplexed LED array)

dmcole wrote:Just an update: Matt is drawing up a new schematic, based on RPM's DMX16 design. After I review it, I'll order up the components from Mouser and build a bread-board version tout de suite.

\dmc

Schematic as promised let me know if you see anything out of place.

And once again thanks to RPM for the source.

the Fets used by RPM are an overkill in the is application. You could get away with a 2803 driver

Matt
BTW the delay has been my changing OS from Vista to Win&. Win7 is real nice. But don't upgrade - blow the old away and start afresh.


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

Re: New project: Sawyer Star (Charlieplexed LED array)

Are you planning to do a basic matrix with this or Charlie-plexing? Just curious since the title says the latter but the design looks like the former?

I agree with using the 2803 - even full on you're talking 150mA per output...


Reply
David_AVD
Posts: 991
(@david-avd)
Noble Member
Joined: 17 years ago

Re: New project: Sawyer Star (Charlieplexed LED array)

At a quick glance, the circuit presented is matrix only. From what I understand, "Charlie-plexing" required push-pull drivers on both outputs.


Reply
Matt_Edwards
Posts: 2664
(@matt-edwards)
Famed Member
Joined: 18 years ago

Title is wrong. this is simple multiplexing.

there will be several stages in the development
First: build a proto that uses Vixen to implement the multiplexing and the LED control - this requires DMX 16ch per Star.

Cct is updated with ULN2803A.

To answer a couple of other questions:
I use 6way Single in Line connectors for ISP. they line up with pins 17,18 & 19 of the Tiny2313. that is X5. X6 is the more traditiional 2x3 pin ISP. choose which you you want you use.
All ICs should have a 100nF as close to the device power pins as possible. these are required to filter the power supply noise inherent in high speed digital switching ccts.
as the timing is not very critical and to keep costs low, a 3 pin ceramic resonator is used in place of the traditional 2pin Crystal and caps.

Cheers


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

Question: is this design intended to support dimming in any form? Or are it a simple on/off project?


Reply
dmcole
Posts: 2196
Topic starter
(@dmcole)
Noble Member
Joined: 19 years ago
P. Short wrote:Question: is this design intended to support dimming in any form? Or are it a simple on/off project?

It is planned to support dimming.

\dmc


Reply
Page 2 / 6
Share: