MonoPixel Animated ...
 
Notifications
Clear all

MonoPixel Animated Candy Canes

103 Posts
17 Users
0 Reactions
70.8 K Views
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

Dave,
Have you ever posted how you 'mounted' these candy canes, including how you routed the wire between canes?

dirknerkle wrote:Ending with a set of 3, you run a separate wire from the data line of the last LED back down to the bottom and that connects to your data line to the driver at the base of the next cane in line. That's your "daisy chain" connection. If you put a ws2811 as your last board at the top of the cane, that will work, but you'll lose 3 channels in the process and you still have to bring a wire down to the base.

Here's the wiki for it:
http://www.diychristmas.org/wiki/index.php?title=Making/Wiring_Mono-Pixels


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago

Ukewarrior, the last part if the wiki explains how the connections between candy canes are made.

Sent from my SM-T710 using Tapatalk


Reply
dirknerkle
Posts: 10310
Topic starter
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

I also added a little section on the base mount I designed for them. A lot better than the weak, plastic spikes that the manufacturers provide, and puts less strain on the plastic candy cane, too.


Reply
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

miss post, deleted.


Reply
pmiller
Posts: 2795
(@pmiller)
Famed Member
Joined: 12 years ago

I had to order more carrier boards. I'm doing 12 canes with 7 pixels (21 channels) each. That's going to be a lot of soldering. Anyway, I created a base which I think is going to work excellent for what I'm doing. I'll post a pick of it tomorrow and a video of the sequencing when I get it done. Took me a little while to figure out connection because my driver boards are different than the ones pictured.

Sent from my SM-T710 using Tapatalk


Reply
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

Thanks. I look forward to seeing what you did.

pmiller wrote:I had to order more carrier boards. I'm doing 12 canes with 7 pixels (21 channels) each. That's going to be a lot of soldering. Anyway, I created a base which I think is going to work excellent for what I'm doing. I'll post a pick of it tomorrow and a video of the sequencing when I get it done. Took me a little while to figure out connection because my driver boards are different than the ones pictured.

Sent from my SM-T710 using Tapatalk


Reply
IdunBenhad
Posts: 1603
(@idunbenhad)
Noble Member
Joined: 18 years ago

Hi:
As usual, Dirk has come up with a neat idea. Thanks, Dave.

Yes, "tinning" that small wire in the suggested cable can be very tedious and time consuming and as UKEWARRIOR said, solid wire can break, but just be aware that there is not much flexing if the project is handled right and carefully. Solid wire is easier to solder than the stranded, but it too, should be tinned before soldering to a board. Using RJ-45 cable by stripping the outer insulation sleeve off should work well. Using 18-20 gauge bell/thermostat wire will make the whole operation a little too "stiff", IMO.

One way to make life a little easier in the tinning department is to clamp the soldering iron in a vice or similar with the tip pointing toward you. Get your cable ends ready to tin and put a small dab of solder on the iron tip. Put the wire to be soldered on the tip, put a small amount of solder on the connection and withdraw the cable end. This way you don't have to try and handle the soldering iron and the solder and the cable at the same time. As pointed out, be careful with the amount of solder you are applying, as the connection can get too large to fit into the hole.

Idun


Reply
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

Hmmmm,
Is an individual strand of RJ45 wire big enough to carry the current for this application?
That would be easy for sure.
I haven't done the math is why I'm asking.

IdunBenhad wrote:Hi:
As usual, Dirk has come up with a neat idea. Thanks, Dave.

Yes, "tinning" that small wire in the suggested cable can be very tedious and time consuming and as UKEWARRIOR said, solid wire can break, but just be aware that there is not much flexing if the project is handled right and carefully. Solid wire is easier to solder than the stranded, but it too, should be tinned before soldering to a board. Using RJ-45 cable by stripping the outer insulation sleeve off should work well. Using 18-20 gauge bell/thermostat wire will make the whole operation a little too "stiff", IMO.

One way to make life a little easier in the tinning department is to clamp the soldering iron in a vice or similar with the tip pointing toward you. Get your cable ends ready to tin and put a small dab of solder on the iron tip. Put the wire to be soldered on the tip, put a small amount of solder on the connection and withdraw the cable end. This way you don't have to try and handle the soldering iron and the solder and the cable at the same time. As pointed out, be careful with the amount of solder you are applying, as the connection can get too large to fit into the hole.

Idun


Reply
IdunBenhad
Posts: 1603
(@idunbenhad)
Noble Member
Joined: 18 years ago

Hi:
According to tables found on the internet(where else?),

Gauge Amps
22--------------5
24--------------3
30--------------.8

Note the cable Dirknerkle used is 30 gauge (I think), so 24 gauge, which is apparently what is in most RJ45 cable should not be a problem.

Idun


Reply
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

Awesome. Easy and cheap, plus I already have it !

IdunBenhad wrote:Hi:
According to tables found on the internet(where else?),

Gauge Amps
22--------------5
24--------------3
30--------------.8

Note the cable Dirknerkle used is 30 gauge (I think), so 24 gauge, which is apparently what is in most RJ45 cable should not be a problem.

Idun


Reply
Page 4 / 11
Share: