Just fooling around.... sent this off to the board shoppe and we'll see what happens. It's a 24-channel controller for external DC SSRs and there's NO PIC TO MESS WITH! Instead, it uses eight WS2811 chips daisy-chained together and an ESP8266 module for communication. The idea is that the ESP is set to pixel mode and the controller board simply extracts the various outputs to RJ45 jacks instead of LEDs. The controller board is 4-1/2" x 1.85" in size and needs external DC power.
Based on the screwy things we did with the mono-pixel candy cane, we think it ought to work. But who knows.... sometimes out-of-the-box thinking backfires bigtime... :w00t:
Sounds like a great idea! Would add a Di and Do connection point to allow inserting this in the middle or at the end of a run of pixels instead of using an esp module.
Sent from my iPhone using Tapatalk
You have DI on the center pin of the 3-pin jumper next to the ESP module's location. DO wouldn't be hard to add -- as is you'd tap pin #5 of the last WS2811 chip, but a header pin could certainly be added for it. Piece of cake.
The jury's out on this thing until after we build a prototype. Should have a trial run of PCBs back in about 10-14 days.
The WS2811 outputs are open collector and are programmed to directly drive 18mA per channel. I don't see any transistors on your board. What DCSSR receiver board did you intend to use with this?
Bill - Maybe I'm wrong here but I thought most DCSSR's were driven in a common-anode arrangement, where the outputs are active low and internally to the DCSSR, the other side of the LED portion of the optocouplers were tied to +5V like so: https://www.doityourselfchristmas.com/wiki/images/0/00/DCSSR2_4_schematic.pdf
If that's the case, open collector on the WS2811 would be essentially doing that, would it not?
Dirk - It needs a jumper to bypass the ESP in favor of a RS485 chip for data in, and at the other end a RS485 always providing data out. That would allow the first board to get data by wireless and daisychain boards down the line.
or, you could just quadruple the number of WS2811 chips and call it Pix-Zilla 🙂
Did you know that 64 WS2811 chips would provide 192 outputs which coincidentally would nicely provide four outputs for each of the jacks on an RJ45 48-port 1U patch panel?
Just throwing that out there 😀
The WS2811 spec states that it's a constant-current 18.5ma/output , and being that it's a common anode device and switching the grounds, it's a nearly perfect match for the common anode SSRs that DIY'ers typically use so electrically, it seems like a pretty good match. Might have to cut down the current a little bit for the SSRs but we'll do some live testing when the protos come back and see if we can make any smoke... (the DIGWDF engineers like that part the best...)
My solution for serial I/O will be to duplicate the 6-pin I/O connection that Renzilla uses because the SISO adapter (485 serial in/485 serial out) is a tried-and-tested product. No need to invent new circuitry when there's already a plug-in option. With SISO attached you logically wouldn't plug an ESP onto the board. (Well, my engineers probably would just to see what happened, but normal people wouldn't...)
And Frederic, I'm one ahead of you on the idea of the 48-port patch panel... did you notice the row of header pins just above the RJ45's? I happen to have a 48-port patch panel in a box that's just sitting there waiting to be used.... the No-Pic controller is small enough to daisy-chain 8 of them and attach them to the back of the panel... TWireless and I made Renzilla with 96 channels and indeed, this would DOUBLE that... Hmmm.... I seem to also have just received a big shipment of WS2811 chips... and another batch of ESP modules...... hmmmmm...... I wonder if...
Okay, use the SISO board as is and put a jumper on this board to switch between SISO and ESP. Just a thought for those who like wireless.
I have ESP modules in piles on my workbench and they work fantastic on the bench, but terrible outside. Probably because in my basement there's no wifi coming in based on how my house is constructed (slate roof, wire mesh lathe with 1" plaster on every wall and ceiling surface, that mesh grounded by the 1941 metal electrical boxes, MC cable, and so on).
Outside the house, even though my neighbors and I are spread apart anywhere from 1/2 to a full acre, wifi is totally saturated with all the access points in the 'hood (I have six myself) plus all the garage openers, cordless phones, and my neighbor across the street has some kind of whole-house automation system that uses 2.4Ghz as well. It's a radio nightmare.
Anyway, I did see the headers when I glanced at the board and that's what triggered my thinking cat5 patch panel. Then, another and another so I could in theory fill up my 3U flight case and probably never ever run out of DCSSR's.
I'm still fighting myself as to what is better - intelligence in the props or centralized and centralized always appeals to a part of my brain in funny ways even though rolling out miles of cat5 can be unpleasant.
Just rambling... but patch panel really works for me no matter what is behind it (dmx, renard, ethernet, DCSSR quad channel stuff) mostly because I have oh I dunno, 20 of these things brand new ready to go that I've put aside specifically for animated lighting.
dirknerkle wrote:And Frederic, I'm one ahead of you on the idea of the 48-port patch panel... did you notice the row of header pins just above the RJ45's? I happen to have a 48-port patch panel in a box that's just sitting there waiting to be used.... the No-Pic controller is small enough to daisy-chain 8 of them and attach them to the back of the panel... TWireless and I made Renzilla with 96 channels and indeed, this would DOUBLE that... Hmmm.... I seem to also have just received a big shipment of WS2811 chips... and another batch of ESP modules...... hmmmmm...... I wonder if...
Yeah. I'm still working out the path I'll be taking in the future, and for some reason I keep coming back to a centralized controller with cat-5 going from there, every which way. I have a 3U flight case ready to go, and I also have a 6U flight case ready to go, depending what I do. probably, the 3U case will be bridges and ethernet, and the 6U case someday will be all patch panels and driving DCSSR's.
FWIW, we ran a little test on the first prototype.... we have a ways to go yet but it looks promising....
<
Cool !
A candy cane driver!
The goal with this little gizmo is to give a person a way to "splice-in" a controller into the pixel string data line that takes up only 8 pixels but allows you to control other things and not just pixel LEDs. I've already tested it with a DirkCheapSSR, for example, and it works fine. It doesn't dim very well because it's not using the ZC signal, but you still have the option to turn an existing AC SSR either ON or OFF. And with 24 channels, you have quite a few options of "things" that you could control that aren't pixels.
It's all about taking existing technology and thinking about it a little differently to accomplish other tasks. You know, INVENTION! 😉
BTW, working on a ZC solution with BarnabyBear, too!

