Finally Affortable ...
 
Notifications
Clear all

Finally Affortable Snowfall Tubes (FAST)

448 Posts
68 Users
0 Reactions
262.9 K Views
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

I have mine set up for one on each channel which is crazy overkill but made the wiring easier - I run four from each Cat5 (4-channels...) and have each running different timings in the FAST code settings so they don't look alike.


Reply
Posts: 86
(@airsouth)
Estimable Member
Joined: 16 years ago

I didn't see a forum area specifically for this device, but this is probably not the right area to post this either. So please forgive me if this post isn't in the right area.

I am very new to the arena. I have built several renard 16 and 24 SS boards, but beyond following instructions I'm just now learning the engineering side of things. That being said, I'm having trouble getting one of these set up. I have everything wired up on a bread board with 7 lights and when I flash the diagnostic or the standard firmware onto my pic (nearly) everything works (see PWM below), but when I try and flash the random version of the firmware, nothing lights up. I can roughly follow along with assembly (high level programmer by trade). I haven't changed anything on the random version that I haven't on the regular. Any insight?

Also, side note: I'm not getting any PWM out of this. The lights are either off or on at full brightness, so the tail isn't showing. Maybe there's something simple that I'm missing here too.


Reply
Posts: 339
(@heldwhat-christmas)
Reputable Member
Joined: 15 years ago
TomL8345 wrote:A lot of people running FAST tubes do not try to control them individually, rather they program the chips with different start times and fall rates (all configurable when you flash the chips) and then they simply run a small 5V PS, or wall wart plugged into a single channel on their AC controller. They look like they are random, yet only use 1 channel for control.

This is what I did.... I have 32 tubes all running off a little wall wart controlled with 1 channel.


Reply
Posts: 339
(@heldwhat-christmas)
Reputable Member
Joined: 15 years ago
airsouth wrote:I didn't see a forum area specifically for this device, but this is probably not the right area to post this either. So please forgive me if this post isn't in the right area.

I am very new to the arena. I have built several renard 16 and 24 SS boards, but beyond following instructions I'm just now learning the engineering side of things. That being said, I'm having trouble getting one of these set up. I have everything wired up on a bread board with 7 lights and when I flash the diagnostic or the standard firmware onto my pic (nearly) everything works (see PWM below), but when I try and flash the random version of the firmware, nothing lights up. I can roughly follow along with assembly (high level programmer by trade). I haven't changed anything on the random version that I haven't on the regular. Any insight?

Also, side note: I'm not getting any PWM out of this. The lights are either off or on at full brightness, so the tail isn't showing. Maybe there's something simple that I'm missing here too.

Is there a reason you are testing these on a bread board? I haven't looked at the code for a while but I don't remember it really using PWM in the traditional sense. If I remember right, each LED gets turned on sequentially but the tail ones just get turned on for a shorter period of time. With the charlieplexing and the speed of these (primarily on the tail) I wouldn't be completely surprised if the higher impedance of the breadboard was the problem but Phil is the real expert here.

Not sure why the random option would have any effect. Honestly I don't think mine behave that differently with each of the random settings. Did you compile all 3 of the hex files yourself so we can rule out a compile problem?


Reply
Posts: 1168
(@keith-r)
Noble Member
Joined: 19 years ago

I was playing with this program the other day, trying to slow down the rate of fall in the random mode. In the modular file, I found that when I changed the line "movlw d'2' " to "movlw d'10'," it was too slow and that was a good thing.
I then tried modifying the lines in the random code:
MOVWF d3
bsf d3, 3 ;####### Comment This line out to make tube possibly go SUPER FAST
bcf d3, 5
bcf d3, 6 ;####### Comment This line out to make tube random much slower
bcf d3, 7 ;End Random Code
; movlw d'2' ;####### Sets Speed of Fall if you want Static Speed uncomment these two lines and put
; movwf d3 '####### a number between the quotes to set speed you like higher num = slower fall

I commented the line "bcf d3, 6 and uncommented the two lines below and changed the movlw d'2' to d'9' or d'10' and it wouldn't compile. Am I missing something here?

I want to use the random mode, but the rate of fall is really too fast for my liking. How can I slow it down?
Thanks.


Reply
Page 76 / 90
Share: