Dumb Led-Triks Disp...
 
Notifications
Clear all

Dumb Led-Triks Display

87 Posts
18 Users
0 Reactions
34 K Views
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

There may be a way to do this without using any micro at all. What I'm thinking of is the FT245 USB chip. You would be somewhat limited, of course, by the USB distance restrictions.


Reply
Penfold
Posts: 1235
(@penfold)
Noble Member
Joined: 19 years ago

There may be a way around the USB distance restriction to an extent. Although it would be fairly expensive and may or may not work. You would have to buy up to five USB 2.0 Extension cables with signal booster, and you could only get it 25 meters (roughly 82 Feet) max according to specs.

http://bestofferbuy.com/BAFO-USB-2.0-Extension-Cable-with-Data-Signal-Power-Amplifier-%285-Meter%29-p-26135.html?currency=USD

This is probably not practical, but I did find it interesting.


Reply
ErnieHorning
Posts: 4434
(@erniehorning)
Famed Member
Joined: 19 years ago
P. Short wrote:There may be a way to do this without using any micro at all. What I'm thinking of is the FT245 USB chip. You would be somewhat limited, of course, by the USB distance restrictions.

150 feet far enough? http://www.pickegg.com/wholesale/45m-150ft-usb-over-rj45-usb-cable-extension-wire-adapter-blue.html?welcome=254


Reply
dirknerkle
Posts: 10311
Topic starter
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
P. Short wrote:You may want to consider using a PIC16F627A (or one of its siblings) instead of the PIC16F688. It is capable of driving eight LEDs at the 25mA level by itself without external transistors. Both parts are capable of driving eight MOC3023-based SSR channels by themselves as well. The PIC16F627A is perhaps two bits more expensive, comes in an 18-pin package, and would require a fairly trivial port of the Renard firmware.

Oops, never mind, this is slightly off-topic. I was distracted...

Thanks, Phil -- not off-topic at all! I've thought about that because the 16F627A is on the Ren-C as I remember, and it drives the 595 or Grinch directly and (probably) has a lot of the shift register/control signals already worked out, right? (I think your name is there in the ASM code anyway...:smile:) AND.... I just happen to have checked my stash of parts last night and lo' and behold, there seem to be a dozen of those pics right there... 😀 along with its sibling, the 16F628A! "Well," I thought to myself, "isn't THAT convenient!" Hmmmmm... lots of options here!!!

(I suspect our Arduino and Propeller supporters are already looking down their noses as this paltry project, but we PIC users are a stalwart and loyal crowd! :mrgreen:)

I'm not sure the FT245 chip would work -- for one reason, part of my goal is to keep this Renard-compatible so it could also be operated wirelessly, and while I haven't looked at the chip yet, I suspect that might require making the display in real-time. The idea I have in mind is to allow the pic to "load" X bytes of information based on the channel data and then continuously display it until the data is replaced, which is a bit different than real-time display. But I'm open to all kinds of ideas as this project starts to get a better focus! Thanks again.

-dave


Reply
dlovely
Posts: 3167
(@dlovely)
Famed Member
Joined: 17 years ago
dirknerkle wrote:AND.... I just happen to have checked my stash of parts last night and lo' and behold, there seem to be a dozen of those pics right there... 😀 along with its sibling, the 16F628A! "Well," I thought to myself, "isn't THAT convenient!" Hmmmmm... lots of options here!!!

Dave, would you quit looking through my parts... LOL, I started with a few 16F627A before I moved to the SX52 for an easy prototype. Was having troubles with interfacing the RTC using the 16F627A. Seems our projects have taken us along the same paths in the past.

Dave


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago
dirknerkle wrote:Thanks, Phil -- not off-topic at all! I've thought about that because the 16F627A is on the Ren-C as I remember, and it drives the 595 or Grinch directly and (probably) has a lot of the shift register/control signals already worked out, right? (I think your name is there in the ASM code anyway...:smile:) AND.... I just happen to have checked my stash of parts last night and lo' and behold, there seem to be a dozen of those pics right there... 😀 along with its sibling, the 16F628A! "Well," I thought to myself, "isn't THAT convenient!" Hmmmmm... lots of options here!!!

It was irrelevant because your idea is to use 595 chips to drive the LEDs, not a micro.

(I suspect our Arduino and Propeller supporters are already looking down their noses as this paltry project, but we PIC users are a stalwart and loyal crowd! :mrgreen:)

I'm not sure the FT245 chip would work -- for one reason, part of my goal is to keep this Renard-compatible so it could also be operated wirelessly, and while I haven't looked at the chip yet, I suspect that might require making the display in real-time. The idea I have in mind is to allow the pick to "load" X bytes of information based on the channel data and then continuously display it until the data is replaced, which is a bit different than real-time display. But I'm open to all kinds of ideas as this project starts to get a better focus! Thanks again.

-dave

If operating wireless is a requirement, then I'm afraid that some sort of micro is necessary. The logic here is that wireless implies serial, and I don't know of any discrete UARTs or USARTs that are easy to obtain these days.

Perhaps it would be best to use a PICAXE chip, since afaik you don't need anything beyond a cable to program them. Despite their expense, I think that a PICAXE might be the easiest thing for a newby to use (at least, I hope that the built-in UART is available for general use).


Reply
dirknerkle
Posts: 10311
Topic starter
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
P. Short wrote:It was irrelevant because your idea is to use 595 chips to drive the LEDs, not a micro.

If operating wireless is a requirement, then I'm afraid that some sort of micro is necessary. The logic here is that wireless implies serial, and I don't know of any discrete UARTs or USARTs that are easy to obtain these days.

Perhaps it would be best to use a PICAXE chip, since afaik you don't need anything beyond a cable to program them. Despite their expense, I think that a PICAXE might be the easiest thing for a newby to use (at least, I hope that the built-in UART is available for general use).

Thanks for the PICAXE idea, too!

And wireless isn't a specific requirement in this case, but compatibility with Renard is because wired or wireless, I want to use an existing transmission protocol for simplicity. That way, a person who had a single SS24, for example, could simply add 8 more channels to his profile, use channels 25-32 for the dumb-triks message and daisy-chain it off the SS24. Since he'd be using Renard, there's a good likelihood he'd have a PIC programmer available (or in this case, a pre-programmed PIC with start_addr 0 would work fine). Or if he wanted wireless, he'd use start_addr 3 and it'd work the same way.

If he didn't have renard but used the parallel or 595 output (which a newbie may do), he'd do roughly the same but he'd add the Renard plugin and set the appropriate channels/port for it and do it that way. I think that's still "newbie-ish" of a way to make it work, eliminates the need to write a new output plugin, and maintains compatibility with existing equipment, but I've been off my rocker before and I may be again! 😆


Reply
dirknerkle
Posts: 10311
Topic starter
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
P. Short wrote:It was irrelevant because your idea is to use 595 chips to drive the LEDs, not a micro.

I still need a driver board, similar to a Ren-C to read, decode, store and repeatedly send the data to the 595 chips to display the message, so the 16F627A is still a good idea for the driver board.


Reply
chelmuth
Posts: 1077
(@chelmuth)
Noble Member
Joined: 16 years ago

I have an idea and I'm wondering if this is maybe something like you're contemplating. Say I have 8 channels dedicated to the Dumb Triks.. I have timing broken down in to what ever ms I want, say 50ms. turning on channel 1 for to start the Dumb triks recording items to display. Then Use channels 2-x for programming in binary. ie. 0001 = a, 0010 = b, 0011 = c, 0100 = d, 0101 = e, etc. Each channel would represent one of the bits. Each 50ms time frame would be equal to one character. Then when done recording all characters turn off channel 1.. then the dumb triks starts to repeat recorded display..


Reply
Posts: 6728
(@p-short)
Illustrious Member
Joined: 20 years ago

Were you thinking of placing the character generator in the PIC, or keeping in the Vixen plugin?


Reply
Page 3 / 9
Share: